Dell PowerEdge R350 EMC Installation and Service Manual - Page 81

System board, Removing the system board

Get Dell PowerEdge R350 PDF manuals and user guides View all Dell PowerEdge R350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Figure 76. Installing the MicroSD card Next steps 1. Install the IDSDM module. 2. Install the air shroud. 3. Follow the procedure listed in the After working inside the system. System board This is a service technician replaceable part only. Removing the system board Prerequisites CAUTION: If you are using the Trusted Platform Module (TPM) with an encryption key, you may be prompted to create a recovery key during program or System Setup. Be sure to create and safely store this recovery key. If you replace this system board, you must supply the recovery key when you restart your system or program before you can access the encrypted data on your drives. 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the following components: a. Air shroud b. Memory modules c. Disconnect the fan cables d. Expansion cards e. Expansion card risers f. M.2 BOSS riser g. Processor h. Heat sink i. Internal USB key (if installed) j. IDSDM k. Disconnect all cables from the system board. CAUTION: Take care not to damage the system identification button while removing the system board from the system. Installing and removing system components 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Figure 76. Installing the MicroSD card
Next steps
1.
Install the IDSDM module
.
2.
Install the air shroud
.
3.
Follow the procedure listed in the
After working inside the system
.
System board
This is a service technician replaceable part only.
Removing the system board
Prerequisites
CAUTION:
If you are using the Trusted Platform Module (TPM) with an encryption key, you may be prompted
to create a recovery key during program or System Setup. Be sure to create and safely store this recovery key.
If you replace this system board, you must supply the recovery key when you restart your system or program
before you can access the encrypted data on your drives.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the following components:
a.
Air shroud
b.
Memory modules
c.
Disconnect the fan cables
d.
Expansion cards
e.
Expansion card risers
f.
M.2 BOSS riser
g.
Processor
h.
Heat sink
i.
Internal USB key (if installed)
j.
IDSDM
k.
Disconnect all cables from the system board.
CAUTION:
Take care not to damage the system identification button while removing the system board
from the system.
Installing and removing system components
81