Dell PowerEdge R740xd2 EMC Installation and Service Manual - Page 108

Removing expansion card from system board, Steps

Get Dell PowerEdge R740xd2 PDF manuals and user guides View all Dell PowerEdge R740xd2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Steps 1. Press and lift up the expansion card retention latch to open. 2. Hold the expansion card by the edges and lift the card to disconnect it from the system board connector. Figure 82. Removing expansion card from system board 3. If the expansion card is not going to be replaced, install a filler bracket by performing the following steps: a. Align the filler bracket with the slot on the system. b. Push the filler bracket downward until firmly seated. c. Close the retention latch by pressing the latch down until the latch snaps into place. 108 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Steps
1.
Press and lift up the expansion card retention latch to open.
2.
Hold the expansion card by the edges and lift the card to disconnect it from the system board connector.
Figure 82. Removing expansion card from system board
3.
If the expansion card is not going to be replaced, install a filler bracket by performing the following steps:
a.
Align the filler bracket with the slot on the system.
b.
Push the filler bracket downward until firmly seated.
c.
Close the retention latch by pressing the latch down until the latch snaps into place.
108
Installing and removing system components