Dell PowerEdge R740xd2 EMC Installation and Service Manual - Page 76

Installing the drive bay 1 backplane bracket

Get Dell PowerEdge R740xd2 PDF manuals and user guides View all Dell PowerEdge R740xd2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Figure 51. Removing bay 1 backplane bracket Next steps Replace the drive bay 1 backplane bracket. Installing the drive bay 1 backplane bracket Prerequisites Follow the safety guidelines listed in Safety instructions. 1. Follow the procedure listed in Before working inside your system. 2. If installed, remove the front bezel. 3. Remove all the drives from drive bay 1. 4. Open the drive bays. Steps 1. Align the backplane bracket with the two slots at the bay base in drive bay 1. 2. Slide the bracket to the left until it is firmly seated and locks into place. 3. Using a Phillips #1 screwdriver, tighten the screws on top of the drive bay to secure the bracket. 76 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Figure 51. Removing bay 1 backplane bracket
Next steps
Replace the drive bay 1 backplane bracket.
Installing the drive bay 1 backplane bracket
Prerequisites
Follow the safety guidelines listed in
Safety instructions
.
1.
Follow the procedure listed in
Before working inside your system.
2.
If installed,
remove the front bezel
.
3.
Remove all the drives from drive bay 1.
4.
Open the drive bays.
Steps
1.
Align the backplane bracket with the two slots at the bay base in drive bay 1.
2.
Slide the bracket to the left until it is firmly seated and locks into place.
3.
Using a Phillips #1 screwdriver, tighten the screws on top of the drive bay to secure the bracket.
76
Installing and removing system components