Dell PowerEdge R740xd2 EMC Installation and Service Manual - Page 132

Steps, To avoid damage to the battery connector

Get Dell PowerEdge R740xd2 PDF manuals and user guides View all Dell PowerEdge R740xd2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

9. Remove the air shroud. 10. If applicable, disconnect the power or data cables from expansion card(s). 11. If installed, remove the low profile or full height X1 expansion card risers. Steps 1. Locate the battery socket. CAUTION: To avoid damage to the battery connector, you must firmly support the connector while installing or removing a battery. 2. Use a plastic scribe to pry out the system battery. Figure 114. Removing the system battery 3. To install a new system battery, hold the battery with the positive side facing up and slide it under the securing tabs. 4. Press the battery into the connector until it snaps into place. Figure 115. Installing the system battery Next steps 1. If removed, install the low profile or full height X1 expansion card risers. 2. If applicable, connect the cables to the expansion card(s). 132 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
9.
Remove the air shroud.
10.
If applicable, disconnect the power or data cables from expansion card(s).
11.
If installed,
remove the low profile or full height X1 expansion card risers
.
Steps
1.
Locate the battery socket.
CAUTION:
To avoid damage to the battery connector, you must firmly support the connector while installing or
removing a battery.
2.
Use a plastic scribe to pry out the system battery.
Figure 114. Removing the system battery
3.
To install a new system battery, hold the battery with the positive side facing up and slide it under the securing tabs.
4.
Press the battery into the connector until it snaps into place.
Figure 115. Installing the system battery
Next steps
1.
If removed,
install the low profile or full height X1 expansion card risers
.
2.
If applicable, connect the cables to the expansion card(s).
132
Installing and removing system components