Dell PowerEdge R740xd2 EMC Installation and Service Manual - Page 117

cooling and airflow inside the system.

Get Dell PowerEdge R740xd2 PDF manuals and user guides View all Dell PowerEdge R740xd2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Steps 1. Unpack the expansion card and prepare it for installation. For instructions, see the documentation accompanying the card. 2. If you are installing a new card, remove the filler bracket. a. Press and lift the expansion card retention latch. b. Pull the filler bracket upward out of the system. Figure 96. Removing the filler bracket NOTE: Store the filler bracket for future use. Filler brackets must be installed in empty expansion card slots to maintain FCC certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. 3. Holding the card on the edges, align the card with the expansion card connector on the system board. 4. Press the expansion card firmly into the expansion card connector on the system board until the card is fully seated. 5. Close the retention latch by pressing the latch down until the latch snaps into place. Installing and removing system components 117

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Steps
1.
Unpack the expansion card and prepare it for installation.
For instructions, see the documentation accompanying the card.
2.
If you are installing a new card, remove the filler bracket.
a.
Press and lift the expansion card retention latch.
b.
Pull the filler bracket upward out of the system.
Figure 96. Removing the filler bracket
NOTE:
Store the filler bracket for future use. Filler brackets must be installed in empty expansion card slots to
maintain FCC certification of the system. The brackets also keep dust and dirt out of the system and aid in proper
cooling and airflow inside the system.
3.
Holding the card on the edges, align the card with the expansion card connector on the system board.
4.
Press the expansion card firmly into the expansion card connector on the system board until the card is fully seated.
5.
Close the retention latch by pressing the latch down until the latch snaps into place.
Installing and removing system components
117