Dell PowerEdge R740xd2 EMC Installation and Service Manual - Page 127

Removing the MicroSD card

Get Dell PowerEdge R740xd2 PDF manuals and user guides View all Dell PowerEdge R740xd2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

Figure 109. Installing optional IDSDM/vFlash card Next steps 1. Install the MicroSD cards. NOTE: Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during removal. 2. Install the air shroud. 3. Install the system cover. 4. Place the system into the rack. For more information, see the Rail Installation Guide available at www.dell.com/poweredgemanuals. 5. Open the drive bays, install all drives, and then close the drive bays. 6. Install the power supply units. 7. Follow the procedure listed in After working inside your system. Removing the MicroSD card Prerequisites 1. Follow the safety guidelines listed in Safety Instructions. 2. Power off the system and all attached peripherals. 3. Disconnect the system from the electrical outlet, and disconnect the peripherals. 4. Open the drive bays, remove all drives, and then close the drive bays. 5. Remove the power supply units. 6. Remove the system from the rack and place it on an ESD work bench. For more information, see the Rail Installation Guide available at www.dell.com/poweredgemanuals. 7. Remove the system cover. 8. Remove the air shroud. 9. Remove the IDSDM or vFlash module. Steps 1. Locate the MicroSD card slot on the IDSDM/vFlash module, and press the card to partially release it from the slot. 2. Hold the MicroSD card and remove it from the slot. NOTE: Temporarily label each MicroSD card with its corresponding slot number after removal. Installing and removing system components 127

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
Figure 109. Installing optional IDSDM/vFlash card
Next steps
1.
Install the MicroSD cards
.
NOTE:
Reinstall the MicroSD cards into the same slots based on the labels you had marked on the cards during
removal.
2.
Install the air shroud
.
3.
Install
the system cover
.
4.
Place the system into the rack. For more information, see the
Rail Installation Guide
available at
www.dell.com/poweredgemanuals
.
5.
Open the drive bays
, install
all drives
, and then
close the drive bays.
6.
Install the
power supply units
.
7.
Follow the procedure listed in
After working inside your system
.
Removing the MicroSD card
Prerequisites
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Power off the system and all attached peripherals.
3.
Disconnect the system from the electrical outlet, and disconnect the peripherals.
4.
Open the drive bays
, remove
all drives
, and then
close the drive bays.
5.
Remove the
power supply units
.
6.
Remove the system from the rack and place it on an ESD work bench. For more information, see the
Rail Installation Guide
available at
www.dell.com/poweredgemanuals
.
7.
Remove the system cover
.
8.
Remove the air shroud
.
9.
Remove the IDSDM or vFlash module.
Steps
1.
Locate the MicroSD card slot on the IDSDM/vFlash module, and press the card to partially release it from the slot.
2.
Hold the MicroSD card and remove it from the slot.
NOTE:
Temporarily label each MicroSD card with its corresponding slot number after removal.
Installing and removing system components
127