Dell PowerStore 3000X EMC PowerStore Network Configuration Guide for PowerSwit - Page 22

Con the out-of-band management switch

Get Dell PowerStore 3000X PDF manuals and user guides View all Dell PowerStore 3000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

NOTE: If OS10EE was factory installed, a perpetual license is already installed on the switch. 4. Repeat the steps for each switch. Configure the out-of-band management switch If you are deploying PowerStore T model perform the following steps to configure the out-of-band (OOB) management switch settings. Prerequisites Each management switch must have the following ports available to connect to PowerStore T model: ● 2 ports for connectivity to the Management Uplink switch. ● 2 ports to connect to PowerStore T model. ● Optional, 1 port for remote discovery. Steps 1. Establish a terminal session to the switch. 2. Enter global configuration mode. configure terminal 3. Configure a hostname for the switch. hostname oobMgmtSwitch 4. Create a management VLAN. interface vlan 100 description managementNetwork no shutdown exit 5. If performing remote discovery, optionally configure an ethernet interface on the switch for the remote discovery workstation. interface ethernet 1/1/1 description discoveryWorkstation switchport access vlan 100 no shutdown exit 6. Configure the management IP address for the switch. NOTE: The following command sample assumes that automatic IP assignment through Dynamic Host Configuration Protocol (DHCP) is enabled on the switch. If automatic IP assignment through DHCP is not enabled, then you do not need to include no ip address dhcp in the commands below. interface mgmt 1/1/1 no shutdown no ip address dhcp ip address 100.0.100.50/24 exit 7. Configure the management route (default gateway) for the switch. management route 0.0.0.0/0 100.0.100.1 exit 22 PowerStore T model: Configure the switches

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
NOTE:
If OS10EE was factory installed, a perpetual license is already installed on the switch.
4.
Repeat the steps for each switch.
Configure the out-of-band management switch
If you are deploying PowerStore T model perform the following steps to configure the out-of-band (OOB) management switch
settings.
Prerequisites
Each management switch must have the following ports available to connect to PowerStore T model:
●
2 ports for connectivity to the Management Uplink switch.
●
2 ports to connect to PowerStore T model.
●
Optional, 1 port for remote discovery.
Steps
1.
Establish a terminal session to the switch
.
2.
Enter global configuration mode.
configure terminal
3.
Configure a hostname for the switch.
hostname oobMgmtSwitch
4.
Create a management VLAN.
interface vlan 100
description managementNetwork
no shutdown
exit
5.
If performing remote discovery, optionally configure an ethernet interface on the switch for the remote discovery
workstation.
interface ethernet 1/1/1
description discoveryWorkstation
switchport access vlan 100
no shutdown
exit
6.
Configure the management IP address for the switch.
NOTE:
The following command sample assumes that automatic IP assignment through Dynamic Host Configuration
Protocol (DHCP) is enabled on the switch. If automatic IP assignment through DHCP is not enabled, then you do not
need to include
no ip address dhcp
in the commands below.
interface mgmt 1/1/1
no shutdown
no ip address dhcp
ip address 100.0.100.50/24
exit
7.
Configure the management route (default gateway) for the switch.
management route 0.0.0.0/0 100.0.100.1
exit
22
PowerStore T model: Configure the switches