Dell Precision 610 Dell Precision WorkStation 610 Mini Tower Systems Service M - Page 18

Using the Network Interface Controller, in

Get Dell Precision 610 PDF manuals and user guides View all Dell Precision 610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

The 10/100-Mbps NIC supports a 10-Mbps direct connection to either a Category 3 or a Category 5 Ethernet cable. When the NIC operates in the 100-Mbps mode, a Category 5 Ethernet cable must be used. Chapter 5, "Using the Network Interface Controller," in the User's Guide provides instructions for connecting the computer to, and configuring it for use on, an Ethernet network. USB capability simplifies connection of peripheral devices such as mice, printers, and computer speakers. The USB connectors on the computer's back panel provide a single connection point for multiple USB-compliant devices. USB-compliant devices can be connected and disconnected while the computer is running. If a processor or hard-disk drive exceeds its recommended operating temperature range, a system event triggers a system management interrupt (SMI), which alerts the BIOS. If the Dell ThermalShutdown Service is installed, the power indicator flashes and a message appears on the monitor to alert the user that the system will shut down in an orderly manner, preventing the loss of data. If the service is unable to shut down the system within approximately 3 minutes, the BIOS powers down the computer. If the ThermalShutdown Service is not installed, the computer turns off immediately. NOTE: The BIOS powers down the computer in the event of a thermal alert only if the Thermal Power-Off category is set to ENABLED in the System Setup program. 1-8 Dell Precision 610 Mini Tower Systems Service Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
1-8
Dell Precision 610 Mini Tower Systems Service Manual
The 10/100-Mbps NIC supports a 10-Mbps direct connection to either a
Category 3 or a Category 5 Ethernet cable. When the NIC operates in the
100-Mbps mode, a Category 5 Ethernet cable must be used.
Chapter 5, “Using the Network Interface Controller,” in the
User’s Guide
pro-
vides instructions for connecting the computer to, and configuring it for use
on, an Ethernet network.
86%
USB capability simplifies connection of peripheral devices such as mice, print-
ers, and computer speakers. The USB connectors on the computer’s back
panel provide a single connection point for multiple USB-compliant devices.
USB-compliant devices can be connected and disconnected while the com-
puter is running.
7KHUPDO±3URWHFWLRQ±
If a processor or hard-disk drive exceeds its recommended operating tempera-
ture range, a system event triggers a system management interrupt (SMI),
which alerts the BIOS. If the Dell ThermalShutdown Service is installed, the
power indicator flashes and a message appears on the monitor to alert the
user that the system will shut down in an orderly manner, preventing the loss
of data. If the service is unable to shut down the system within approximately
3 minutes, the BIOS powers down the computer. If the ThermalShutdown Ser-
vice is not installed, the computer turns off immediately.
NOTE: The BIOS powers down the computer in the event of a thermal alert
only if the Thermal Power-Off category is set to ENABLED in the System Setup
program.