Dell Precision 610 Dell Precision WorkStation 610 Mini Tower Systems Service M - Page 79

processor or a Dell terminator card. If a slot is not occupied, or if a non-Dell ter

Get Dell Precision 610 PDF manuals and user guides View all Dell Precision 610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

To install a Slot 2 SEC cartridge/heat sink assembly, press the cartridge firmly into its connector until it is firmly seated. You must use up to 25 pounds of force to fully seat the cartridge in its connector. Place the top bracket on top of the cartridge. Install the four large thumbscrews through the top bracket holes and through the holes in the guide bracket assembly to secure the heat sink to the system board. NOTE: Both processor slots must be populated with either a Pentium II Xeon processor or a Dell terminator card. If a slot is not occupied, or if a non-Dell terminator card is installed, the system will not power on. If necessary, change the processor speed jumper setting (see Figure 4-17 to locate system board jumpers). The processor speed jumper should be set for the installed processor's rated internal speed. For example, for a 400-MHz Intel Pentium II Xeon processor, a jumper plug should be installed on the pins labeled "400MHZ." (See Chapter 1, "System Board Jumpers," for more information on the jumpers.) The processor speed jumper setting must not exceed the slowest internal speed of either processor. Removing and Replacing Parts 4-25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Removing and Replacing Parts
4-25
To install a Slot 2 SEC cartridge/heat sink assembly, press the cartridge firmly
into its connector until it is firmly seated. You must use up to 25 pounds of
force to fully seat the cartridge in its connector. Place the top bracket on top of
the cartridge. Install the four large thumbscrews through the top bracket holes
and through the holes in the guide bracket assembly to secure the heat sink to
the system board.
NOTE: Both processor slots must be populated with either a Pentium II Xeon
processor or a Dell terminator card. If a slot is not occupied, or if a non-Dell ter-
minator card is installed, the system will not power on.
If necessary, change the processor speed jumper setting (see Figure 4-17 to
locate system board jumpers).
The processor speed jumper should be set for the installed processor’s rated
internal speed. For example, for a 400-MHz Intel Pentium II Xeon processor, a
jumper plug should be installed on the pins labeled “400MHZ.” (See Chapter 1,
“System Board Jumpers,” for more information on the jumpers.) The processor
speed jumper setting must not exceed the slowest internal speed of either
processor.