Epson ActionPrinter 3000 User Manual - Page 41

Paper Handling 2-9, emerges between the platen and the ribbon guide. Pull the paper

Get Epson ActionPrinter 3000 - ActionPrinter-3000 Impact Printer PDF manuals and user guides View all Epson ActionPrinter 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Using Continuous Paper 3. Slide the left sprocket unit to approximately 0.5 inches (12 mm) from the far left position and push the lever back to lock it in place. Then slide the right sprocket unit to match the width of your paper, but do not lock it. 4 Position the paper support midway between the two sprocket units. Open both sprocket covers. 5 Make sure your paper has a clean, straight edge. Then insert the paper into the desired paper slot (rear or bottom) until it emerges between the platen and the ribbon guide. Pull the paper up to the sprocket units. 6. Fit the holes of the paper over the tractor pins of the sprocket units, and then close the sprocket covers. Paper Handling 2-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Using Continuous Paper
3.
Slide the left sprocket unit to approximately 0.5 inches (12 mm)
from the far left position and push the lever back to lock it in
place. Then slide the right sprocket unit to match the width of
your paper, but do not lock it.
4
5
Position the paper support midway between the two sprocket
units. Open both sprocket covers.
Make sure your paper has a clean, straight edge. Then insert the
paper into the desired paper slot (rear or bottom) until it
emerges between the platen and the ribbon guide. Pull the paper
up to the sprocket units.
6.
Fit the holes of the paper over the tractor pins of the sprocket
units, and then close the sprocket covers.
Paper Handling 2-9