Fluke TI450 SF6 User Manual - Page 40

Color Alarms, Set High-Temperature Color Alarm

Get Fluke TI450 SF6 PDF manuals and user guides View all Fluke TI450 SF6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Ti200, Ti300, Ti400,Ti450 Users Manual When you are in Auto Level and Span mode, and not in a sub-menu, you can use the up and down arrows to quickly adjust the blending. Push / to change the blending between 100% infrared, 75%, 50%, 25%, and full visible in Full AutoBlend or Picture-in-Picture mode. Color Alarms The Imager has various apparent temperature color alarms. The hightemperature color alarm shows a full visible image and only shows infrared information on objects or areas that are above the set apparent temperature alarm level. The low-temperature (or dew point) color alarm shows a full visible image and only shows infrared information on objects or areas that are below the set apparent temperature (or set dew point) color alarm level. The user must manually determine and set these parameters. The imager also displays color isotherms, or infrared information, inside or outside of a set of both high and low limits. Note The Imager does not sense ambient or surface dew point level automatically. To use the low-temperature color alarm function as a dew point color alarm, manual determination and input of surface dew point temperature will yield the best results. Depending on the situation, the colors presented may help identify areas of concern with possible dew point condensation. To view the Color Alarm menu: 1. Go to Image > Color Alarm. 2. Push  to view the menu. Set High-Temperature Color Alarm To set a high-temperature color alarm: 1. Go to Image > Color Alarm > Set High Alarm. 2. Push / to adjust the temperature setting. 3. Push  or  set the new value. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Ti200, Ti300, Ti400,Ti450
Users Manual
36
When you are in Auto Level and Span mode, and not in a sub-menu, you can
use the up and down arrows to quickly adjust the blending.
Push
/
to change the blending between 100% infrared, 75%, 50%,
25%, and full visible in Full AutoBlend or Picture-in-Picture mode.
Color Alarms
The Imager has various apparent temperature color alarms. The high-
temperature color alarm shows a full visible image and only shows infrared
information on objects or areas that are above the set apparent temperature
alarm level. The low-temperature (or dew point) color alarm shows a full visible
image and only shows infrared information on objects or areas that are below
the set apparent temperature (or set dew point) color alarm level. The user
must manually determine and set these parameters. The imager also displays
color isotherms, or infrared information, inside or outside of a set of both high
and low limits.
Note
The Imager does not sense ambient or surface dew point level
automatically. To use the low-temperature color alarm function as a
dew point color alarm, manual determination and input of surface dew
point temperature will yield the best results. Depending on the
situation, the colors presented may help identify areas of concern with
possible dew point condensation.
To view the Color Alarm menu:
1.
Go to
Image
>
Color Alarm
.
2.
Push
to view the menu.
Set High-Temperature Color Alarm
To set a high-temperature color alarm:
1.
Go to
Image
>
Color Alarm
>
Set High Alarm
.
2.
Push
/
to adjust the temperature setting.
3.
Push
or
set the new value.