HP DL320 HP ProLiant DL320 Generation 2 Server Maintenance and Service Guide - Page 20

Bezel Blank, Removing the bezel blank

Get HP DL320 - ProLiant - G3 PDF manuals and user guides
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Removal and Replacement Procedures Bezel Blank To remove the bezel blank: 1. Power down the server. See "Powering Down the Server" in this chapter. 2. Remove the shipping/ejector key from the chassis if you have not already done so. See "Shipping/Ejector Key" in this chapter. 3. Insert the end of the shipping/ejector key approximately 1.25 cm (0.5 in) into the optical device/diskette drive assembly ejector port on the lower right corner of the server front panel (1) to eject the blank (2). Figure 2-3: Removing the bezel blank To replace the bezel blank, slide the blank into the empty bay until it locks into place. Store the shipping/ejector key in the chassis or other safe location for future use. HP ProLiant DL320 Generation 2 Server Maintenance and Service Guide 2-9 HP CONFIDENTIAL Codename: Moonstar 306 Part Number: 293164-004 Last Saved On: 9/22/03 1:47 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Removal and Replacement Procedures
Bezel Blank
To remove the bezel blank:
1.
Power down the server. See “Powering Down the Server” in this chapter.
2.
Remove the shipping/ejector key from the chassis if you have not already done so. See
“Shipping/Ejector Key” in this chapter.
3.
Insert the end of the shipping/ejector key approximately 1.25 cm (0.5 in) into the optical
device/diskette drive assembly ejector port on the lower right corner of the server front
panel (1) to eject the blank (2).
Figure 2-3:
Removing the bezel blank
To replace the bezel blank, slide the blank into the empty bay until it locks into place. Store
the shipping/ejector key in the chassis or other safe location for future use.
HP ProLiant DL320 Generation 2 Server Maintenance and Service Guide
2-9
HP CONFIDENTIAL
Codename: Moonstar 306 Part Number: 293164-004 Last Saved On: 9/22/03 1:47 PM