HP DesignJet T795 Using your printer - Page 154

The whole image is blurry or grainy, The paper is not flat, Speed, Quality

Page 154 highlights

The whole image is blurry or grainy 1. Check that the paper type you have loaded corresponds to the paper type selected in the front panel and in your software. See View information about the paper on page 40. 2. Check that you are printing on the correct side of the paper. 3. Check that you are using appropriate print-quality settings (see Printing on page 46). In some cases, you can overcome a print-quality problem merely by selecting a higher print-quality level. For instance, if you have set the Print Quality slider to Speed, try setting it to Quality. If you change the print-quality settings, you may wish to reprint your job at this point in case the problem has been solved. 4. Go to the front panel and press and then to see the printhead alignment status. If the status is PENDING, you should align the printheads. See Align the printheads on page 159. After alignment, you may wish to reprint your job in case the problem has been solved. 5. Go to the front panel and press and then to see the paper advance calibration status. If the status is DEFAULT, you should perform paper advance calibration: see Recalibrate the paper advance on page 138. If the problem persists despite all the above actions, contact your customer service representative for further support. The paper is not flat If the paper does not lie flat when it comes out of the printer, but has shallow waves in it, you are likely to see defects in the printed image, such as vertical stripes. This can happen when you use thin paper that becomes saturated with ink. 146 Chapter 17 Troubleshooting print-quality issues ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192

The whole image is blurry or grainy
1.
Check that the paper type you have loaded corresponds to the paper type selected in the front panel and in
your software. See
View information about the paper
on page
40
.
2.
Check that you are printing on the correct side of the paper.
3.
Check that you are using appropriate print-quality settings (see
Printing
on page
46
). In some cases, you
can overcome a print-quality problem merely by selecting a higher print-quality level. For instance, if you
have set the Print Quality slider to
Speed
, try setting it to
Quality
. If you change the print-quality settings,
you may wish to reprint your job at this point in case the problem has been solved.
4.
Go to the front panel and press
and then
to see the printhead alignment status. If the status is
PENDING, you should align the printheads. See
Align the printheads
on page
159
. After alignment, you
may wish to reprint your job in case the problem has been solved.
5.
Go to the front panel and press
and then
to see the paper advance calibration status. If the
status is DEFAULT, you should perform paper advance calibration: see
Recalibrate the paper advance
on page
138
.
If the problem persists despite all the above actions, contact your customer service representative for further
support.
The paper is not
flat
If the paper does not lie
flat
when it comes out of the printer, but has shallow waves in it, you are likely to see
defects in the printed image, such as vertical stripes. This can happen when you use thin paper that becomes
saturated with ink.
146
Chapter 17
Troubleshooting print-quality issues
ENWW