HP EliteDesk 800 G3 Maintenance and Service Guide - Page 52

Installing a 9.5 mm slim optical drive

Get HP EliteDesk 800 G3 PDF manuals and user guides View all HP EliteDesk 800 G3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

4. Push the green release latch on the right rear side of the drive toward the center of the drive (1), and then slide the drive forward and out of the bay (2). Installing a 9.5 mm slim optical drive 1. Prepare the computer for disassembly (Preparation for disassembly on page 19) 2. Remove the access panel (Access panel on page 20) 3. Remove the front bezel (Front bezel on page 21). If you are installing a drive in a bay covered by a bezel blank, remove the bezel blank. See Removing bezel blanks on page 23 for more information. 4. Disconnect the power cable (1) and data cable (2) from the rear of the drive. IMPORTANT: When removing the cables, pull the tab or connector instead of the cable itself to avoid damaging the cable. 42 Chapter 4 Removal and replacement procedures - Microtower (MT) chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
4.
Push the green release latch on the right rear side of the drive toward the center of the drive
(1)
, and
then slide the drive forward and out of the bay
(2)
.
Installing a 9.5 mm slim optical drive
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
19
)
2.
Remove the access panel (
Access panel
on page
20
)
3.
Remove the front bezel (
Front bezel
on page
21
). If you are installing a drive in a bay covered by a bezel
blank, remove the bezel blank. See
Removing bezel blanks
on page
23
for more information.
4.
Disconnect the power cable
(1)
and data cable
(2)
from the rear of the drive.
IMPORTANT:
When removing the cables, pull the tab or connector instead of the cable itself to avoid
damaging the cable.
42
Chapter 4
Removal and replacement procedures – Microtower (MT) chassis