HP EliteDesk 800 G3 Maintenance and Service Guide - Page 62

Removing and installing an M.2 SSD storage card, Remove the drive cage

Get HP EliteDesk 800 G3 PDF manuals and user guides View all HP EliteDesk 800 G3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

5. Connect the power cable (1) and data cable (2) to the rear of the hard drive. NOTE: If the 2.5-inch hard drive is the primary drive, connect the other end of the data cable to the dark blue SATA connector on the system board labeled SATA0. If it is a secondary hard drive, connect the other end of the data cable to one of the light blue SATA connectors on the system board. 6. Reassemble the computer. Removing and installing an M.2 SSD storage card NOTE: The computer supports 2230 and 2280 M.2 SSD cards. 1. Prepare the computer for disassembly (Preparation for disassembly on page 19) 2. Remove the access panel (Access panel on page 20) 3. Remove the drive cage (Drive cage on page 28) 4. To remove an M.2 SSD card, remove the screw that secures the card (1), lift the end of the card up (2), and then slide the card out of the system board connector (3). 52 Chapter 4 Removal and replacement procedures - Microtower (MT) chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
5.
Connect the power cable
(1)
and data cable
(2)
to the rear of the hard drive.
NOTE:
If the 2.5-inch hard drive is the primary drive, connect the other end of the data cable to the
dark blue SATA connector on the system board labeled SATA0. If it is a secondary hard drive, connect the
other end of the data cable to one of the light blue SATA connectors on the system board.
6.
Reassemble the computer.
Removing and installing an M.2 SSD storage card
NOTE:
The computer supports 2230 and 2280 M.2 SSD cards.
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
19
)
2.
Remove the access panel (
Access panel
on page
20
)
3.
Remove the drive cage (
Drive cage
on page
28
)
4.
To remove an M.2 SSD card, remove the screw that secures the card
(1)
, lift the end of the card up
(2)
,
and then slide the card out of the system board connector
(3)
.
52
Chapter 4
Removal and replacement procedures – Microtower (MT) chassis