HP EliteDesk 800 G3 Maintenance and Service Guide - Page 73

Hood sensor, A tool such as a screwdriver may

Get HP EliteDesk 800 G3 PDF manuals and user guides View all HP EliteDesk 800 G3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Hood sensor The hood sensor is installed on the top, rear of the chassis. 1. Prepare the computer for disassembly (Preparation for disassembly on page 19). 2. Remove the access panel (Access panel on page 20). 3. Disconnect the cable from the system board connector labeled HSENSE (1). 4. Slide the hood sensor out of the slot on the rear of the chassis (2). A tool such as a screwdriver may be required to pry the hood sensor from the slot. To install the hood sensor, reverse the removal procedure. Hood sensor 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
Hood sensor
The hood sensor is installed on the top, rear of the chassis.
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
19
).
2.
Remove the access panel (
Access panel
on page
20
).
3.
Disconnect the cable from the system board connector labeled HSENSE
(1)
.
4.
Slide the hood sensor out of the slot on the rear of the chassis
(2)
. A tool such as a screwdriver may be
required to pry the hood sensor from the slot.
To install the hood sensor, reverse the removal procedure.
Hood sensor
63