HP EliteDesk 800 G8 Maintenance and Service Guide - Page 49

Option board

Get HP EliteDesk 800 G8 PDF manuals and user guides View all HP EliteDesk 800 G8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

2. Using a screwdriver or similar tool, slide the sensor out of the slot in the rear of the chassis (2). To install the hood sensor, reverse the removal procedure. Option board To remove the option board, use these procedures. For a list of available option boards, see Computer major components on page 6. Before removing the option board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 21). 2. Remove the access panel (see Access panel on page 21). 3. Depending on model, remove the air duct (see Air duct on page 38. Remove the option board: 1. Remove the two Phillips screws (1) that secure the board to the system board. 2. Lift to disengage the board from the system board connector, and then remove the option board from the computer (2). Option board 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
2.
Using a screwdriver or similar tool, slide the sensor out of the slot in the rear of the chassis
(2)
.
To install the hood sensor, reverse the removal procedure.
Option board
To remove the option board, use these procedures.
For a list of available option boards, see
Computer major components
on page
6
.
Before removing the option board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
21
).
2.
Remove the access panel (see
Access panel
on page
21
).
3.
Depending on model, remove the air duct (see
Air duct
on page
38
.
Remove the option board:
1.
Remove the two Phillips screws
(1)
that secure the board to the system board.
2.
Lift to disengage the board from the system board connector, and then remove the option board from
the computer
(2)
.
Option board
41