HP LH4r HP Netserver LP 2000r User Guide - Page 116

HP Netserver.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

Chapter 13 Alternative Rack Mounting (4-Post) Marking the Columns To make it easier to install the slides in the rack, you may want to mark the columns to indicate the server placement. Use the HP Rack Configuration Tools to determine where in the rack to mount the HP Netserver. The tools are available at the following URL: http://www.hp.com/netserver/support 1. Use a marking pen or masking tape to mark the server position on the inside of the front and rear columns, as shown in Figure 13-2. The slides will use the second column hole, counting from the base of the HP Netserver. Inside Face of Column Rear of Rack Masking Tape or Marker Left Side Mark this face of the columns with masking tape or marker pen. Right Side Bottom of HP NetServer Front of Rack Figure 13-2. Marking Server Placement 110

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Chapter 13
Alternative Rack Mounting (4–Post)
110
Marking the Columns
To make it easier to install the slides in the rack, you may want to mark the
columns to indicate the server placement. Use the
HP Rack Configuration Tools
to determine where in the rack to mount the HP Netserver. The tools are available
at the following URL:
1.
Use a marking pen or masking tape to mark the server position on the
inside of the front and rear columns, as shown in Figure 13-2.
The slides will use the second column hole, counting from the base of the
HP Netserver.
Front of
Rack
Mark this face of
the columns with
masking tape
or marker pen.
Right
Side
Left
Side
Rear of
Rack
Bottom of
HP NetServer
Masking
Tape or
Marker
Inside Face of Column
Figure 13-2.
Marking Server Placement