HP LH4r HP Netserver LP 2000r User Guide - Page 27

Removing Hot Swap Hard Drives

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Chapter 3 Installing Mass Storage Devices 4. Make sure the drive is pushed in completely. Close the ejector arms and press them in until the latch clicks into place. See Figure 3-4. Figure 3-4. Closing Drive Ejector Arms 5. Verify that the drive is flush with the other drives. If the drive is not flush, it is not seated properly in the drive slot. Open the ejector arms and repeat Step 3 and 4. Make sure that you open the ejector arms wide before inserting the drive in the slot. Push the drive in completely before attempting to close the ejector arms. Removing Hot Swap Hard Drives CAUTION Remove the drive slowly. Wait for the drive heads to park before completely removing the drive. Follow the instructions carefully to prevent damage to the drive head and head actuator. 1. To unlock the drive, insert your thumb into the opening at the center of the drive and pull the ejector arms outward until they click into the open position. See Figure 3-5. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Chapter 3
Installing Mass Storage Devices
21
4.
Make sure the drive is pushed in completely.
Close the ejector arms and
press them in until the latch clicks into place. See Figure 3-4.
Figure 3-4. Closing Drive Ejector Arms
5.
Verify that the drive is flush with the other drives. If
the drive is not flush,
it is not seated properly in the drive slot.
Open the ejector arms and repeat
Step 3 and 4.
Make sure that you open the ejector arms wide before inserting the drive in
the slot. Push the drive in completely before attempting to close the ejector
arms.
Removing Hot Swap Hard Drives
CAUTION
Remove the drive slowly. Wait for the drive heads to park
before completely removing the drive.
Follow the instructions
carefully to prevent damage to the drive head and head
actuator.
1.
To unlock the drive, insert your thumb into the opening at the center of
the drive and pull the ejector arms outward until they click into the
open position. See Figure 3-5.