HP LH4r HP Netserver LP 2000r User Guide - Page 35

Installing Additional Memory

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

4 Installing Additional Memory Introduction The HP Netserver LP 2000r's main memory is implemented using four memory slots on the system board which support up to 4 GB (1 GB x 4) of memory. The Netserver uses only 3.3V, 168-pin, 133 MHz SDRAM DIMMs and ships with at least one 256 MB DIMM. The embedded video controller is provided with 4 MB standard video memory and cannot be upgraded. NOTE Use only PC 133 (133 MHz) SDRAM DIMMs acquired from Hewlett-Packard. The EDO DIMMs and PC 100 SDRAM DIMMs from earlier HP Netserver models will fit into the DIMM slots in the Netserver, but the EDO DIMMs and PC 100 SDRAM will not function properly. To ensure you have the correct DIMMs before installation, refer to one of the following for a list of qualified DIMMs: • HP Order Assistant on the HP web site at: http://www.hp.com/netserver • HP Customer Service Tools Required The following tools are required to install DIMMs in the HP Netserver. • An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
29
4
Installing Additional Memory
Introduction
The HP Netserver LP 2000r’s main memory is implemented using four memory
slots on the system board which support up to 4 GB (1 GB x 4) of memory. The
Netserver uses only 3.3V, 168-pin, 133 MHz SDRAM DIMMs and ships with at
least one 256 MB DIMM. The embedded video controller is provided with 4 MB
standard video memory and cannot be upgraded.
NOTE
Use only PC 133 (133 MHz) SDRAM DIMMs acquired from
Hewlett-Packard. The EDO DIMMs and PC 100 SDRAM
DIMMs from earlier HP Netserver models will fit into the
DIMM slots in the Netserver, but the EDO DIMMs and PC 100
SDRAM will not function properly.
To ensure you have the correct DIMMs before installation, refer to one of the
following for a list of qualified DIMMs:
•
HP Order Assistant on the HP web site at:
•
HP Customer Service
Tools Required
The following tools are required to install DIMMs in the HP Netserver.
•
An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist
strap.