HP LH4r HP Netserver LP 2000r User Guide - Page 44

Installing an Accessory Board

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Chapter 5 Installing Additional Boards Integrated RA Board I2C Connector Figure 5-2. Integrated RA Board Location Installing an Accessory Board Use this procedure to install the accessory board. NOTE For information about a specific PCI board type, refer to the Readme file, Tested Products List, or Configuration Advisor on your HP Netserver Navigator CD-ROM. 1. Log off all users and, if necessary, back up files. For detailed instructions, see "Powering Down the HP Netserver," in Chapter 1, "Controls, Ports and Indicators." 2. Press the power switch on the HP Netserver control panel to turn off power when prompted by the operating system. 3. Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the HP Netserver chassis out from the rack as far as it can be extended. It is not necessary to remove the HP Netserver from the rack to install an accessory board. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Chapter 5
Installing Additional Boards
38
Integrated
RA Board
I C
Connector
2
Figure 5-2. Integrated RA Board Location
Installing an Accessory Board
Use this procedure to install the accessory board.
NOTE
For information about a specific PCI board type, refer to the
Readme file, Tested Products List, or Configuration Advisor on
your
HP Netserver Navigator CD-ROM
.
1.
Log off all users and, if necessary, back up files.
For detailed instructions, see "Powering Down the HP Netserver," in
Chapter 1, "Controls, Ports and Indicators."
2.
Press the power switch on the HP Netserver control panel to turn off power
when prompted by the operating system.
3.
Pull out the anti-tip foot at the bottom of the rack. Then slowly slide the
HP Netserver chassis out from the rack as far as it can be extended.
It is not necessary to remove the HP Netserver from the rack to install an
accessory board.