HP LH4r HP Netserver Service Handbook, Volume 2 - Mid - Page 165

Non-duplex, disk array model with PCI controller board standard model, Default Switch Settings,

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 165 highlights

Non-duplex, disk array model with PCI controller board (standard model) Flexible Disk External terminator T built into cable Drive CD-ROM IDE C1 SCSI or IDE Device 68 to 50 pin adapter A T System Board Internal C2 terminator built into I2C board PCI Board SCSI B SCSI A C3 C2 C2 Ext Conn Hot Swap Subsystem This cable must be routed through the rear access hole located below the controller board Off On UPPER CAGE 1 SCSI ID 2 3 ID ID ID 4 1 2 3 5 6 UPPER CAGE LOWER CAGE 1 2 3 ID ID ID 4 5 6 4 LOWER CAGE 5 6 Default Switch Settings These are the default SCSI settings that come with this model. The standard model includes a PCI controller board. The CD-ROM drive is set for SCSI ID 5. To change the SCSI addresses, see Configuring Switch Settings on the Hot Swap Subsystem. 157

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
157
Non-duplex, disk array model with PCI controller board (standard model)
Hot Swap
Subsystem
SCSI or IDE
Device
CD-ROM
System Board
IDE
PCI Board
Ext Conn
SCSI A
SCSI B
T
A
Flexible Disk
Drive
T
IC
2
External terminator
built into cable
68 to 50 pin
adapter
Internal
terminator
built into
board
C1
C2
C3
C2
C2
This cable must be routed through the rear
access hole located below the controller board
UPPER
CAGE
1
2
3
4
5
6
LOWER
CAGE
1
2
3
4
5
6
6
5
4
1
2
3
SCSI ID
UPPER CAGE
LOWER CAGE
ID
ID
ID
ID
ID
ID
Off
On
Default Switch Settings
These are the default SCSI settings that come with this model. The
standard model includes a PCI controller board. The CD-ROM drive
is set for SCSI ID 5. To change the SCSI addresses, see
Configuring Switch Settings on the Hot Swap Subsystem
.