HP ProLiant DL160se HP ProLiant DL160se G6 Server Maintenance and Service Guid - Page 37

System cover, Top cover

Get HP ProLiant DL160se - G6 Server PDF manuals and user guides View all HP ProLiant DL160se manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

System cover You need to remove the top cover before you can remove or replace a server component. The top cover needs to be removed to service the SAS/SATA backplane. Top cover To remove the top cover: 1. Loosen the screw on the top cover with a T-10 wrench. 2. Press the latch on the top cover. 3. Slide the cover toward the rear of the server and then lift the top cover to remove it from the chassis. Lift the top cover away from the chassis. Figure 1 Removing the Top Cover To reinstall the top cover: 1. Align the top cover to the chassis and then slide it towards the front panel to position it into place. 2. Once the cover is attached to the chassis, tighten the screw on the top cover with a T-10 wrench. Removal and replacement procedures 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Removal and replacement procedures
37
System cover
You need to remove the top cover before you can remove or replace a server component. The top
cover needs to be removed to service the SAS/SATA backplane.
Top cover
To remove the top cover:
1.
Loosen the screw on the top cover with a T-10 wrench.
2.
Press the latch on the top cover.
3.
Slide the cover toward the rear of the server and then lift the top cover to remove it from the
chassis. Lift the top cover away from the chassis.
Figure 1
Removing the Top Cover
To reinstall the top cover:
1.
Align the top cover to the chassis and then slide it towards the front panel to position it into
place.
2.
Once the cover is attached to the chassis, tighten the screw on the top cover with a T-10 wrench.