HP ProLiant DL160se HP ProLiant DL160se G6 Server Maintenance and Service Guid - Page 53

Removal and replacement procedures, Removing the Non-hot-plug Hard Drive Disk

Get HP ProLiant DL160se - G6 Server PDF manuals and user guides View all HP ProLiant DL160se manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Figure 21 Removing the Non-hot-plug Hard Drive Disk To install a non-hot-plug hard drive disk into the carrier: 1. Put the non-hot-plug hard drive disk into the carrier. 2. Fasten the HDD to the carrier using the screws (two on each side). Figure 22 Installing the Non-hot-plug Hard Drive Disk into the Carrier To install a non-hot-plug hard drive into the server: 1. Remove the hard drive blank from the front of the system if installed. 2. Push the hard drive assembly into the drive bay until it stops. Removal and replacement procedures 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Removal and replacement procedures
53
Figure 21
Removing the Non-hot-plug Hard Drive Disk
To install a non-hot-plug hard drive disk into the carrier:
1.
Put the non-hot-plug hard drive disk into the carrier.
2.
Fasten the HDD to the carrier using the screws (two on each side).
Figure 22
Installing the Non-hot-plug Hard Drive Disk into the Carrier
To install a non-hot-plug hard drive into the server:
1.
Remove the hard drive blank from the front of the system if installed.
2.
Push the hard drive assembly into the drive bay until it stops.