HP ProLiant DL380 ProLiant DL380 Generation 2 Server Maintenance and Service G - Page 67

PPMs

Get HP ProLiant DL380 - G2 Server PDF manuals and user guides View all HP ProLiant DL380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

PPMs Removal and Replacement Procedures To remove a PPM: 1. Power down the server. See the "Powering Down the Server" section in this chapter. 2. Extend or remove the server from the rack. See the "Preparation Procedures" section in this chapter. 3. Remove the access panel. See the "Access Panel" section in this chapter.  4. Open the latches on the sides of the PPM slots .  5. Lift the PPM out of the slot . 1 2 1 Figure 2-49: Removing a PPM CAUTION: PPM slots must be populated when processors are installed. If PPM slots are not populated, the system does not boot. IMPORTANT: PPMs do not seat if turned the wrong way. Reverse steps 1 through 5 to replace the PPM. Compaq ProLiant DL380 Generation2 Server Maintenance and Service Guide 2-53 COMPAQ CONFIDENTIAL Codename: Magna Part Number: 203840-003 Last Saved On: 1/28/02 1:12 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Removal and Replacement Procedures
Compaq ProLiant DL380 Generation2 Server Maintenance and Service Guide
2-53
COMPAQ CONFIDENTIAL
Codename: Magna Part Number: 203840-003 Last Saved On: 1/28/02 1:12 PM
PPMs
To remove a PPM:
1.
Power down the server. See the
“
Powering Down the Server
”
section in this chapter.
2.
Extend or remove the server from the rack. See the
“
Preparation Procedures
”
section in
this chapter.
3.
Remove the access panel. See the
“
Access Panel
”
section in this chapter.
4.
Open the latches on the sides of the PPM slots
.
5.
Lift the PPM out of the slot
.
1
2
1
Figure 2-49:
Removing a PPM
CAUTION:
PPM slots must be populated when processors are installed. If PPM slots are not
populated, the system does not boot.
IMPORTANT:
PPMs do not seat if turned the wrong way.
Reverse steps 1 through 5 to replace the PPM.