HP ProLiant DL380 ProLiant DL380 Generation 2 Server Maintenance and Service G - Page 74

Rear Fan Bracket, Remove the system board. See

Get HP ProLiant DL380 - G2 Server PDF manuals and user guides View all HP ProLiant DL380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Removal and Replacement Procedures Rear Fan Bracket To remove the rear fan bracket: 1. Power down the server. See the "Powering Down the Server" section in this chapter. 2. Extend or remove the server from the rack. See the "Preparation Procedures" section in this chapter. 3. Remove the access panel. See the "Access Panel" section in this chapter. 4. Remove the PCI riser cage. See the "PCI Riser Cage" section in this chapter. 5. Remove the air baffle. See the "Air Baffle" section in this chapter. 6. Remove all hot-plug fans. See the "Hot-Plug Fan" section in this chapter. 7. Remove the front fan bracket. See the "Front Fan Bracket" section in this chapter. 8. Remove the system board. See the "System Board" section in this chapter. NOTE: When removing the system board, you may leave the DIMMs, the processors, the PPMs, the Smart Array 5i Controller, and the system battery on the system board, unless you are replacing them as failed items. 9. Use a Torx T-15 screwdriver to remove the screws that secure the rear fan bracket to the  system board .  10. Rotate the rear fan bracket toward the edge of system board and remove the bracket . 2 1 1 Figure 2-55: Removing the rear fan bracket Reverse steps 1 through 10 to replace the rear fan bracket. 2-60 Compaq ProLiant DL380 Generation2 Server Maintenance and Service Guide COMPAQ CONFIDENTIAL Codename: Magna Part Number: 203840-003 Last Saved On: 1/28/02 1:12 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Removal and Replacement Procedures
2-60
Compaq ProLiant DL380 Generation2 Server Maintenance and Service Guide
COMPAQ CONFIDENTIAL
Codename: Magna Part Number: 203840-003 Last Saved On: 1/28/02 1:12 PM
Rear Fan Bracket
To remove the rear fan bracket:
1.
Power down the server. See the
“
Powering Down the Server
”
section in this chapter.
2.
Extend or remove the server from the rack. See the
“
Preparation Procedures
”
section in
this chapter.
3.
Remove the access panel. See the
“
Access Panel
”
section in this chapter.
4.
Remove the PCI riser cage. See the
“
PCI Riser Cage
”
section in this chapter.
5.
Remove the air baffle. See the
“
Air Baffle
”
section in this chapter.
6.
Remove all hot-plug fans. See the
“
Hot-Plug Fan
”
section in this chapter.
7.
Remove the front fan bracket. See the
“
Front Fan Bracket
”
section in this chapter.
8.
Remove the system board. See the
“
System Board
”
section in this chapter.
NOTE:
When removing the system board, you may leave the DIMMs, the processors, the PPMs, the
Smart Array 5i Controller, and the system battery on the system board, unless you are replacing them
as failed items.
9.
Use a Torx T-15 screwdriver to remove the screws that secure the rear fan bracket to the
system board
.
10. Rotate the rear fan bracket toward the edge of system board and remove the bracket
.
1
1
2
Figure 2-55:
Removing the rear fan bracket
Reverse steps 1 through 10 to replace the rear fan bracket.