HP Server tc3100 hp server remote management card user guide - Page 23

Connecting the 50-pin Ribbon Cable to the Server

Get HP Server tc3100 PDF manuals and user guides View all HP Server tc3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Chapter 3 Hardware Installation and Configuration Server is powered down. Serious injury may result if this warning is not observed. 2. You must plug the Remote Management Card into slot 6. Connecting the 50-pin Ribbon Cable to the Server After you have physically installed the HP Server Remote Management Card into slot 6 of your server, you must cable the card to the server's system board. One end of the supplied ribbon cable should already be connected to the Remote Control Card (see previous section). Connect the other end to the system board's 50-pin connector that is immediately adjacent to the inserted card. NOTE The ribbon cable is keyed to prevent incorrect cable connection. Figure 3-2: Installing the Remote Management Card 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Chapter 3
Hardware Installation and Configuration
Server is powered down. Serious injury may result if this
warning is not observed.
2.
You must plug the Remote Management Card into slot 6.
Connecting the 50-pin Ribbon Cable to the Server
After you have physically installed the HP Server Remote Management Card into
slot 6 of your server, you must cable the card to the server's system board. One
end of the supplied ribbon cable should already be connected to the Remote
Control Card (see previous section). Connect the other end to the system board’s
50-pin connector that is immediately adjacent to the inserted card.
NOTE
The ribbon cable is keyed to prevent incorrect cable
connection.
Figure 3-2:
Installing the Remote Management Card
17