HP Server tc3100 hp server remote management card user guide - Page 8

Remote Management Card see Appendix I for detailed instructions

Get HP Server tc3100 PDF manuals and user guides View all HP Server tc3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Chapter 1 Quick Start 2. Install the HP Server Remote Management Card in PCI slot 6. 3. Connect the free end of the 50-pin ribbon cable to the 50-pin connector on the server's system board. The connector is keyed. IMPORTANT After you have installed the HP Server Remote Management Card, you must flash the server system BIOS. Flashing the BIOS populates the sensor data repository on the Remote Management Card. This is required to make environmental data available to the Management Card's web interface. Install and connect the Diagnostic Card that was shipped with your HP Server Remote Management Card (see Appendix I for detailed instructions): Set up the remote connection (see Chapter 4 for detailed instructions): 1. Set up the LAN or modem connection that allows the HP Server Remote Management Card to communicate with a remote client: ◊ For a LAN connection: Connect your dedicated 10/100Base-T compatible LAN line to the card's RJ-45 LAN connector. ◊ For a modem connection: Connect a serial modem cable (not provided) to the card's serial port and connect the other end to an external modem. 2. Boot the server. During Power-On Self-Test, when prompted, press F3 to enter the HP Server Remote Management Card BIOS setup program. ◊ If you plan on connecting to the HP Server Remote Management Card via the LAN: Define card's TCP/IP properties (either use a unique IP Address for the card, subnet mask, and gateway, or enable DHCP and have your DHCP server assign these addresses for you). ◊ If you plan on connecting to the HP Server Remote Management Card via modem: Define the card's PPP settings (modem initialization string, IP address, subnet mask). Typically, you would leave the PPP IP address and PPP subnet mask at the factory defaults since your PPP connection does not interact with the site network. 3. Save the configuration and exit. 4. At a remote client running Microsoft Windows NT 4.0 or Windows 95, 98, ME or 2000: 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Chapter 1
Quick Start
2.
Install the HP Server Remote Management Card in PCI slot 6.
3.
Connect the free end of the 50-pin ribbon cable to the 50-pin connector on
the server's system board. The connector is keyed.
IMPORTANT
After you have installed the HP Server Remote Management
Card, you must flash the server system BIOS. Flashing the
BIOS populates the sensor data repository on the Remote
Management Card. This is required to make environmental
data available to the Management Card’s web interface.
Install and connect the Diagnostic Card that was shipped with your HP Server
Remote Management Card (see Appendix I for detailed instructions):
Set up the remote connection (see Chapter 4 for detailed instructions):
1.
Set up the LAN or modem connection that allows the HP Server Remote
Management Card to communicate with a remote client:
◊
For a LAN connection
: Connect your dedicated 10/100Base-T
compatible LAN line to the card's RJ-45 LAN connector.
◊
For a modem connection:
Connect a serial modem cable (not
provided) to the card's serial port and connect the other end to an
external modem.
2.
Boot the server. During Power-On Self-Test, when prompted, press F3 to
enter the HP Server Remote Management Card BIOS setup program.
◊
If you plan on connecting to the HP Server Remote Management
Card via the LAN:
Define card's TCP/IP properties (either use a
unique IP Address for the card, subnet mask, and gateway, or enable
DHCP and have your DHCP server assign these addresses for you).
◊
If you plan on connecting to the HP Server Remote Management
Card via modem:
Define the card's PPP settings (modem initialization
string, IP address, subnet mask). Typically, you would leave the PPP
IP address and PPP subnet mask at the factory defaults since your PPP
connection does not interact with the site network.
3. Save the configuration and exit.
4.
At a remote client running Microsoft Windows NT 4.0 or Windows 95, 98,
ME or 2000:
2