HP StorageWorks 7410 HP StorageWorks Virtual Array va 7000 family - Installati - Page 35

Installing CommandView SDM Software - storageworks software

Get HP StorageWorks 7410 - Virtual Array PDF manuals and user guides View all HP StorageWorks 7410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Installing CommandView SDM Software ■ If you are adding an array to a new system that will require the installation of the CommandView SDM software, continue with "Install CommandView SDM software" ■ If you are adding an array to an existing system that is currently being managed using CommandView SDM, you must add the new array to the management configuration. Perform the following steps to do this. 1 From a CommandView SDM host connected to the array, type the following command: armdiscover Depending on the complexity of the system configuration, the discovery process may take several minutes to complete. 2 Continue with "Gather Host WWNs". Step 17. Install CommandView SDM software Native operating systems CommandView SDM is supported and can be installed on a host or client running one of the following native operating systems. All array management can be done from a host or client running CommandView SDM. - HP-UX 11.00/11.11 - Windows 2000/NT 4.0 - Red Hat Linux 7.1 Non-native operating systems The HP StorageWorks Virtual Array products are supported on the following non-native operating systems. However, CommandView SDM is not supported on these operating systems. CommandView SDM must be installed on a management station running one of the native operating systems, and all array management must be done from there. - Sun Solaris - IBM AIX - NetWare - MPE/iX - HP-UX 10.20 Virtual Array Installation Guide 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Virtual Array Installation Guide
35
Installing CommandView SDM Software
■
If you are adding an array to a new system that will require the installation
of the CommandView SDM software, continue with
"Install CommandView
SDM software"
■
If you are adding an array to an existing system that is currently being
managed using CommandView SDM, you must add the new array to the
management configuration. Perform the following steps to do this.
1
From a CommandView SDM host connected to the array, type the
following command:
armdiscover
Depending on the complexity of the system configuration, the discovery
process may take several minutes to complete.
2
Continue with
"Gather Host WWNs"
.
Step 17. Install CommandView SDM software
Native operating systems
CommandView SDM is supported and can be installed on a host or client
running one of the following native operating systems. All array management
can be done from a host or client running CommandView SDM.
—
HP-UX 11.00/11.11
—
Windows 2000/NT 4.0
—
Red Hat Linux 7.1
Non-native operating systems
The HP StorageWorks Virtual Array products are supported on the following
non-native operating systems. However, CommandView SDM is not supported
on these operating systems. CommandView SDM must be installed on a
management station running one of the native operating systems, and all
array management must be done from there.
—
Sun Solaris
—
IBM AIX
—
NetWare
—
MPE/iX
—
HP-UX 10.20