HP TouchSmart 520-1010t Getting Started - Page 48

Remote control, Memory card reader, Symptom, Possible solution, Start, Device Manager

Get HP TouchSmart 520-1010t PDF manuals and user guides View all HP TouchSmart 520-1010t manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Remote control Symptom Remote sensor is not receiving a signal from the remote control. Possible solution Be sure to point the remote control at the sensor. Be sure the remote control has fresh batteries. For an external sensor with a USB connector, try enabling the IR connection by following these steps: 1 Click the Start button. 2 Type Device Manager into the Start Search box, and then click Device Manager to open the Device Manager window. 3 Click the plus sign (+) next to Universal Serial Bus controllers. 4 If eHome Infrared Receiver is listed under Universal Serial Bus Controllers, Windows 7 is properly detecting the IR receiver. If it is not listed, go to the next step. 5 Unplug the end of the USB cable on the remote sensor from the computer, and then plug it back into the same USB connector. 6 Disconnect all other USB devices, leaving the remote sensor connected, and then restart the computer. Connect other USB devices after the remote sensor appears in the Device Manager window. Memory card reader Symptom Memory card reader cannot read the memory card. Possible solution Do not insert or remove memory cards when the in-use (activity) light is flashing. Doing so may cause data loss or permanent damage to the card reader. Some memory cards have a Read/Write or a Security switch. Ensure the switch is set to Write Enabled before you attempt to write data to the card. Ensure the amount of stored data does not exceed the storage limit of the memory card. 44 Getting Started (features vary by model)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
44
Getting Started (features vary by model)
Remote control
Symptom
Possible solution
Remote sensor is not
receiving a signal from
the remote control.
±
Be sure to point the remote control at the sensor.
±
Be sure the remote control has fresh batteries.
±
For an external sensor with a USB connector, try enabling
the IR connection by following these steps:
1
Click the
Start
button.
2
Type
Device Manager
into the Start Search box, and then
click
Device Manager
to open the Device Manager
window.
3
Click the plus sign (
+
) next to Universal Serial Bus
controllers.
4
If eHome Infrared Receiver
is listed under Universal Serial
Bus Controllers, Windows 7 is properly detecting the
IR receiver. If it is not listed, go to the next step.
5
Unplug the end of the USB cable on the remote sensor
from the computer, and then plug it back into the same
USB connector.
6
Disconnect all other USB devices, leaving the remote
sensor connected, and then restart the computer. Connect
other USB devices after the remote sensor appears in the
Device Manager window.
Memory card reader
Symptom
Possible solution
Memory card reader
cannot read the
memory card.
Do not insert or remove memory cards when the in-use (activity)
light is flashing. Doing so may cause data loss or permanent
damage to the card reader.
Some memory cards have a Read/Write or a Security switch.
Ensure the switch is set to Write Enabled before you attempt to
write data to the card.
Ensure the amount of stored data does not exceed the storage
limit of the memory card.