Hitachi C8FSE Instruction Manual - Page 16

Warning, Caution - laser

Page 16 highlights

English 9. Position adjustment of laser line (Only Model C8FSHE) WARNING: * Make sure before plugging the power plug into the receptacle that the main body and the laser marker are turned off. * Exercise utmost caution in handling a switch trigger for the position adjustment of the laser line, as the power plug is plugged into the receptacle during operation. If the switch trigger is pulled inadvertently, the saw blade can rotate and result in unexpected accidents. * Do not remove the laser marker to be used for other purposes. CAUTION: Fig. 16 Fig. 17 * Laser radiation- Do not stare into beam. * Laser radiation on work table. Do not stare into beam. If your eye is exposed directly to the laser beam, it can be hurt. * Do not dismantle it. * Do not give strong impact to the laser marker (main body of tool); otherwise, the position of a laser line can go out of order, resulting in the damage of the laser marker as well as a shortened service life. * Keep the laser marker lit only during a cutting operation. Prolonged lighting of the laser marker can result in a shortened service life. * Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. NOTE: * Perform cutting by overlapping the ink line with the laser line. * When the ink line and the laser line are overlapped, the strength and weakness of light will change, resulting in a stable cutting operation because you can easily discern the conformity of lines. This ensures the minimum cutting errors. * In outdoor or near-the-window operations, it may become difficult to observe the laser line due to the sunlight. Under such circumstances, move to a place that is not directly under the sunlight and engage in the operation. * Do not tug on the cord behind the motor head or hook your finger, wood and the like around it; otherwise, the cord may come off and the laser marker may not be lit up. Laser line Switch (For laser marker) Ink lining can be easily made on this tool to the laser marker. A switch lights up the laser marker. (Fig. 18) Depending upon your cutting choice, the laser line can be aligned with the left side of the cutting width (saw blade) or the ink line on the right side. The laser line is adjusted to the width of the saw blade at the time of factory shipment. Adjust the positions of the saw blade and the laser line taking the following steps to suit the use of your choice. Fig. 18 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96

16
English
Switch
(For laser marker)
Laser line
Fig. 18
9.
Position adjustment of laser line (Only Model C8FSHE)
WARNING:
* Make sure before plugging the power plug into the receptacle that the main body
and the laser marker are turned off.
* Exercise utmost caution in handling a switch trigger for the position adjustment of
the laser line, as the power plug is plugged into the receptacle during operation.
If the switch trigger is pulled inadvertently, the saw blade can rotate and result in
unexpected accidents.
* Do not remove the laser marker to be used for other purposes.
CAUTION:
* Laser radiation- Do not stare into beam.
* Laser radiation on work table. Do not stare into beam.
If your eye is exposed directly to the laser beam, it can be hurt.
* Do not dismantle it.
* Do not give strong impact to the laser marker (main body of tool); otherwise, the
position of a laser line can go out of order, resulting in the damage of the laser
marker as well as a shortened service life.
* Keep the laser marker lit only during a cutting operation. Prolonged lighting of the
laser marker can result in a shortened service life.
* Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
NOTE:
* Perform cutting by overlapping the ink line with the laser line.
* When the ink line and the laser line are overlapped, the strength and weakness of light will
change, resulting in a stable cutting operation because you can easily discern the conformity
of lines. This ensures the minimum cutting errors.
* In outdoor or near-the-window operations, it may become difficult to observe the laser line
due to the sunlight. Under such circumstances, move to a place that is not directly under the
sunlight and engage in the operation.
*Do not tug on the cord behind the motor head or hook your finger, wood and the like around
it; otherwise, the cord may come off and the laser marker may not be lit up.
Ink lining can be easily made on this tool to the laser marker. A
switch lights up the laser marker. (Fig. 18)
Depending upon your cutting choice, the laser line can be aligned
with the left side of the cutting width (saw blade) or the ink line on
the right side.
The laser line is adjusted to the width of the saw blade at the time
of factory shipment. Adjust the positions of the saw blade and the
laser line taking the following steps to suit the use of your choice.
Fig. 17
Fig. 16