Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste Installation Guid - Page 12

AC Power and Backup Battery - i

Get Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste - LYNXRPK-2 - Wireless Self-Contained Security System PDF manuals and user guides
UPC - 781410916135
View all Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

LYNXR-2 Series Installation and Setup Guide AC Power and Backup Battery The system is powered by a 9VAC, 25VA Plug-in Transformer, ADEMCO K10145X10 (K10145CN in Canada). Refer to the wiring table below for wire gauge and length. Distance from Transformer to Control Up to 75 feet 75 to 150 feet 150 to 300 feet Wire Gauge #20 #18 #16 Use only the provided ADEMCO K10145X10 or K10145CN Transformer. Wiring to the AC Transformer must not exceed 300 feet using 16-gauge wire. The voltage reading between terminals 15 and 16 of the control must not fall below 9.00VAC. Do not plug the transformer into the AC outlet until after all wiring connections have been made. Backup battery In the event of an AC power loss, the system is supported by a long life backup battery that is supervised for connection and for low voltage conditions. If the battery is missing, or a low battery condition is detected, a "low battery" message is displayed and a report is sent to the central station. In addition, the system will beep once every 45 seconds to audibly indicate a low battery condition (press any key to stop the beeping). AC Power and Rechargeable Backup Battery Connecting AC Power and backup battery 1. Connect wires from the K10145X10 (K10145CN) in Canada) AC Transformer to terminals 15 and 16 as shown in the wiring diagram. 2. Remove battery retainer. 3. Peel the backing from tape on the back plate. 4. Insert battery pack into back plate. 5. Install battery retainer. 6. Connect battery connector to receptacle on terminal block PC board. 7. After all wiring connections have been made, snap the front assembly to the back plate and plug the transformer into a 24-hour, 110VAC unswitched outlet. Note: Rechargeable batteries may take up to 48-hours to fully charge. The "LOW BAT" message should clear within four hours or by entering Test Mode. BATTERY PACK RETAINER NOTE LYNXRCHKIT-HC BATTERY PACK SHOWN TAPE BATTERY RECEPTACLE Ensure the cover is snapped closed prior to applying AC power. WIRING TERMINALS 09012-003-V0 - 12 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
LYNXR-2 Series Installation and Setup Guide
- 12 -
AC Power and Backup Battery
The system is powered by a 9VAC, 25VA Plug-in Transformer,
ADEMCO K10145X10 (K10145CN
in
Canada). Refer to the wiring table below for wire gauge and length.
Distance from Transformer to Control
Wire Gauge
Up to 75 feet
#20
75 to 150 feet
#18
150 to 300 feet
#16
Use only the provided ADEMCO K10145X10 or K10145CN Transformer.
Wiring to the AC Transformer
must not exceed 300 feet using 16-gauge wire. The voltage reading between terminals 15 and 16 of the
control must not fall below 9.00VAC.
Do not plug the transformer into the AC outlet until after all wiring connections have been made.
Backup battery
In the event of an AC power loss, the system is supported by a long life backup battery that is supervised for
connection and for low voltage conditions. If the battery is missing, or a low battery condition is detected, a
“low battery” message is displayed and a report is sent to the central station. In addition, the system will beep
once every 45 seconds to audibly indicate a low battery condition (press any key to stop the beeping).
AC Power and Rechargeable Backup Battery
Connecting AC Power and backup battery
1.
Connect wires from the K10145X10 (K10145CN) in
Canada) AC Transformer to terminals 15 and 16 as
shown in the wiring diagram.
2. Remove battery retainer.
3. Peel the backing from tape on the back plate.
4. Insert battery pack into back plate.
5. Install battery retainer.
6. Connect battery connector to receptacle on terminal
block PC board.
7. After all wiring connections have been made, snap the
front assembly to the back plate and plug the
transformer into a 24-hour, 110VAC unswitched outlet.
Note:
Rechargeable batteries may take up to 48-hours to
fully charge. The “LOW BAT” message should clear
within four hours or by entering Test Mode.
09012-003-V0
BATTERY
RECEPTACLE
WIRING
TERMINALS
NOTE
LYNXRCHKIT-HC
BATTERY PACK SHOWN
TAPE
BATTERY
PACK
RETAINER
Ensure the cover is snapped closed prior to applying AC power.