Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste Installation Guid - Page 26

LYNXR-2 Series Installation and Setup Guide Data Field Descriptions Fields ✻47: Field *47 is used to program different options in the LYNXR-2 and LYNXR-2SIA controls. Please be sure that you use the correct field for the control being installed. ✻47 Phone System Select LYNXR-2 SELECTIONS Central Dialing Mode Station Pulse Tone Pulse No WATS 0 = No Speaker Phone 1 = No Speaker Phone 4 = With Speaker Phone WATS 2 = No Speaker Phone 3 = No Speaker Phone 6 = With Speaker Phone Tone 5 = With Speaker Phone 7 = With Speaker Phone LYNXR-2SIA SELECTIONS Central Dialing Mode Station No WATS WATS No WATS WATS Pulse 0 = No Speaker Phone Call Wait Cancel Disabled 2 = No Speaker Phone Call Wait Cancel Disabled 8 = No Speaker Phone Call Wait Cancel Enabled 10 = No Speaker Phone Call Wait Cancel Enabled Tone 1 = No Speaker Phone Call Wait Cancel Disabled 3 = No Speaker Phone Call Wait Cancel Disabled 9 = No Speaker Phone Call Wait Cancel Enabled 11 = No Speaker Phone Call Wait Cancel Enabled Pulse 4 = With Speaker Phone Call Wait Cancel Disabled 6 = With Speaker Phone Call Wait Cancel Disabled 12 = with Speaker Phone Call Wait Cancel Enabled 14 = With Speaker Phone Call Wait Cancel Enabled Tone 5 = With Speaker Phone Call Wait Cancel Disabled 7 = With Speaker Phone Call Wait Cancel Disabled 13 = With Speaker Phone Call Wait Cancel Enabled 15 = With Speaker Phone Call Wait Cancel Enabled ✻48 Report Format for Primary/ Secondary Primary See choices below Secondary See choices below 0 = 3+1; 4+1 ADEMCO Low Speed Standard 1 = 3+1; 4+1 Radionics Standard 2 = 4+2 ADEMCO Low Speed Standard 3 = 4+2 Radionics Standard 5 = ADEMCO Contact ID® Reporting with 10-digit subscriber account number 6 = 4+2 ADEMCO Express 7 = ADEMCO Contact ID® Reporting with 4-digit subscriber account number 8 = 3+1; 4+1 ADEMCO Low Speed Expanded 9 = 3+1; 4+1 Radionics Expanded This option is used to enter the correct type of phone dialing (pulse or tone), and to select the correct WATS line option for the Central Station. This option is used to activate the Speaker Phone option. For the LYNXR-2SIA it is also used to disable call waiting. Note: If using pulse dialing, you must enter the numbers slowly in order to allow the pulse dialer time to operate. LYNXR-2SIA ONLY Call waiting warning tones can interfere with Central stations reporting. The Call Waiting Cancel option should be selected if the reporting phone line has call waiting service. The Call Waiting Cancel command must also be programmed in Field ✻40. If the Call Waiting Cancel feature is enabled, make sure to enter Call Waiting Cancel command in Field ✻40. The command depends on a telephone service provider. Important Note: If Call Wait Cancel is disabled in Field ✻47, and Call Waiting Disable command is entered in Field ✻40, this will prevent successful communication to the central station when used on a non-call waiting line. Note: PABX number and operation of the control panel with a PBX system cannot be used if the Call Waiting Cancel option has been enabled in Field ✻47. Enter ✻ as the 4th digit of ✻43 through ✻44, if 3+1 dialer reporting is to be used. (For an explanation of these formats, see the System Communication section of this manual.) Notes: (1) The maximum number of alarm and alarm restore reports during one armed period is determined by field ✻92. (2) If Option 5 is selected a 10-digit account number must be entered in Fields ✻43 or ✻44. (3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must be selected for AAV. - 26 -