Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste Installation Guid - Page 29

LYNXR-2 Series Installation and Setup Guide Data Field Descriptions ✻55 Reporting Channels 0 = Telco Line (no Radio) 1 = LRR/IP(Digital Communication only) and Telco Line 3 = LRR/IP (Digital Communication only) (no Telco Line) 5 = LRR/IP (Digital Communication with AAV) (Telco Line Connections for 2-way voice seesion only, if applicable) This option is used to enable/disable Central Station reporting via the LRR/IP Communications Device (See Field *77). Upload/ download via the Internet IP module is not affected by this entry. The option specifies the channel that the control will use when sending reports to the Central Station (Follow Me phone, and Pager). Select some or all channels as required. IMPORTANT NOTE Make sure that selected channels are physically available and functional. Note: Zone 103 can not be bypassed. Field ✻57: Field *57 only applies to the LYNXR-2SIA control. ✻57 False Alarm Options Note: This field applies only to the LYNXR-2SIA control. LYNXR-2SIA SELECTIONS Value Cancel Alarm Display Auto Stay Arming Exit Time Restart/ Reset 0 = Disabled Disabled Disabled 1 = Disabled Disabled Enabled 2 = Disabled Enabled Disabled 3 = Disabled Enabled Enabled 4 = Enabled Disabled Disabled 5 = Enabled Disabled Enabled 6 = Enabled Enabled Disabled 7 = Enabled Enabled Enabled Note: The LYNXR-2SIA control validates the data entered in this field. If the selection is not valid the control will emit a single long beep indicating that the selection has been rejected. The control replaces the selection with the default value "7", which is displayed on the keypad, and advances to the next field. Cancel Alarm Display This option enables the display of aborted and cancelled alarms on the LYNXR-2SIA keypad. "CA" will be displayed. Notes: 1. An abort occurs if the alarm panel is disarmed before it dials the alarm report to the central station. 2. A cancel occurs if the alarm panel is disarmed after the alarm is reported. 3. Zone types 5, 6 and 7 (panic zone types) and 24 (silent burglary) cannot be cancelled. Auto Stay Arming If this feature is enabled and the control panel has been armed "Armed Away" at the LYNX keypad or RF keypad, the system will switch to the "Armed Stay" mode if the Exit Time has expired and no exit has been made. Exit Time Restart-Exit Delay Restart/Reset This option allows the systems to restart the exit delay time after arming in STAY mode by entering the User Code and pressing the STAY key (if quick arming is disabled) or by pressing the STAY key (if quick arming is enabled). This option also enables automatic exit delay reset, which resets exit delay if the entry/exit door is re-opened and closed before exit delay time expires after arming. Notes: 1. This avoids the need to disarm and then re-arm the system after allowing someone to enter or exit. 2. Automatic Exit Delay Reset occurs only once during an armed period. ✻58 RF Jam Detection For Event Logging, Option 2 must be selected. 0 = no jam detection 1 = RF jam detection with event logging, but no central station report 2 = RF jam detection with event logging and with central station report (if trouble/restore report is enabled in fields ✻60, ✻71) If the control detects an RF Jam condition, a "FAULT" message appears for zone 90. The Contact ID® code for RF Jam is 344. SYSTEM STATUS AND RESTORE REPORT CODES PROGRAMMING (✻59 - ✻76, & ✻89) Program Report Codes using the interactive *56 Enhanced Zone Programming Mode, or codes can be entered in data fields *59-*76 and *89. Use the following guidelines when programming report codes. The actual report code digits entered depend upon the particular installation, and should be in agreement with you and the central station office receiving the signals. Field *59 is used to program different features in the LYNXR-2 and LYNXR-2SIA controls. Please be sure that you use the correct field for the control being installed. With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1-9, A, B, C, D, E, or F. Enter "#+10" for A (reports a "0" on some receivers), "#+11" for B, "#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F. Entering "0" in the first box will disable a report. Entering "0" in the second box results in automatic advance to the next field. - 29 -