Husqvarna AUTOMOWER 435X AWD Owner Manual - Page 32

Days /

week

h / day

Schedule settings

7

3.5

10:00 - 13:30 / 10

am - 1.30 pm

3.12.2 Operation

In

Operation

you can change the

operation settings of the product. To

change the settings, obey the

instructions in the Automower

®

Connect app.

3.12.2.1 Weather timer

The

Weather timer

automatically adjust the

cutting time to the growth of the grass. The

product is not permitted to operate more than the

schedule settings.

Note:

When using

Weather timer

, it is

recommended to make as much operating time

as possible available for the

Weather timer

. Do

not restrict the schedule more than necessary.

The first operation of the day is set by the

schedule settings. The product always complete

1 mowing cycle, and then the

Weather timer

selects if the product will continue to operate or

not.

Note:

The

Weather timer

is reset if the product

does not operate for more than 50 hours, or if a

Reset of all user settings

is done. The

Weather

timer

is not changed if a

Reset of schedule

settings

is done.

To set the Weather timer

1.

Select

Settings > Operation

in the app.

2.

Select

on/off

to enable or disable the

Weather timer

.

Note:

If the cutting results are not

satisfactory, the cutting time can be

adjusted. Set the cutting time

High

to cut for

a longer time or

Low

to cut for a shorter

time.

3.

Select

Save

.

3.12.2.2 ECO mode

If

ECO mode

is activated, it switches off the

signal in the boundary loop, the guide wire and

the charging station, when the product is parked

or is charging.

Note:

Use

ECO mode

to save energy and avoid

interference with other equipment, for example

hearing loops or garage doors.

Note:

To start the product manually in the work

area, push the

STOP

button before you remove

the product from the charging station. If not, the

product can not be started in the work area.

To set the ECO mode

1.

Select

Settings > Operation

in the app.

2.

Select

on/off

to enable or disable the

ECO

mode

function.

3.

Select

Save

.

3.12.3 Installation

In

Installation

you can change the

installation settings of the product. To

change the settings, obey the

instructions in the Automower

®

Connect app.

3.12.3.1 To find the charging station

The product can be set to search for the charging

station in 3 methods:

•

Charging station signal

•

Follow boundary wire

•

Follow guide wire

The factory setting is set to use the 3 search

methods at the same time. Use the factory

setting to find the charging station as fast as

possible and to keep the risk of tracks on the

lawn to a minimum. The product always starts to

search for the

Charging station signal

. After a

specified time interval, it also uses

Follow guide

and

Follow boundary wire

.

Causes why the product cannot follow the wire:

•

Obstacles near the wire have not been

isolated.

•

The charging station, the boundary wire or

the guide wire are not installed according to

32

- Installation

1404 - 002 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Access	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the battery	6
General manual instructions	6
Automower® Access	6
Display	7
To operate Automower® Access	8
Menu structure overview in Automower® Access	9
Menu structure overview 1	11
Menu structure overview 2	12
Menu structure overview 3	13
LED status indicator	14
Safety	15
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	15
Safety definitions	16
Safety instructions for operation	16
Use	16
Battery safety	17
How to lift and move the product	18
Maintenance	18
In the event of a thunderstorm	19
Installation	20
Introduction - Installation	20
Main components for installation	20
General preparations	20
Before the installation of the wires	20
To examine where to put the charging station	20
To examine where to put the power supply	21
To examine where to put the boundary wire	21
To put the boundary wire in a slope	23
Passages	23
To make an island	23
To make a secondary area	24
To examine where to put the guide wire	25
Work area examples	25
Installation of the product	25
Installation tools	25
To install the charging station	26
To install the boundary wire	27
To install the guide wire	27
To put the wire into position with stakes	28
To bury the boundary wire or the guide wire	28
To extend the boundary wire or the guide wire	28
After the installation of the product	29
To do a visual check of the charging station	29
Automower® Connect	29
To install the Automower® Connect app	29
To pair Automower® Connect and the product	29
My mowers	29
Firmware over the air (FOTA)	29
To set the Firmware over the air (FOTA)	29
Automower® Direct	29
To start to use Automower® Direct	30
User interface overview	30
To start the product for the first time	30
Settings in Automower® Connect	31
Schedule	31
To edit the schedule settings	31
To add a new schedule setting	31
To calculate the schedule setting	31
Operation	32
Weather timer	32
To set the Weather timer	32
ECO mode	32
To set the ECO mode	32
Installation	32
To find the charging station	32
To change the signal range of the charging station	33
To set the delay time for the guide wire and the boundary wire	33
Lawn coverage	33
To set the GPS function	33
To set the Lawn Coverage function	33
To measure the distance from the charging station	34
To do a test of the Lawn Coverage function	34
Drive Past Wire	34
To set the Drive past wire	34
Starting point	34
To set the starting point	34
Accessories	34
Headlights	34
To set the headlight settings	34
To set the headlight to flash when fault	34
To avoid collisions with the mower house	35
General (Bluetooth® only)	35
Time & date	35
To set the time & date	35
Reset to factory settings	35
To reset to factory settings	35
Security (Bluetooth® only)	35
New loop signal	35
To create a New loop signal	35
To change the PIN code	35
Theft protection	35
Require PIN code	35
Alarm duration	35
STOP button pressed	35
Carried away	36
To set the Theft protection	36
GeoFence	36
To set the center position for the GeoFence function	36
Automower® Connect (Bluetooth® only)	36
Messages	36
Operation	37
To switch on the product	37
Operating modes	37
Main area	37
Secondary area (2nd area)	37
Park	37
Park until further notice	38
Park for a selected number of hours	38
To stop the product	38
To switch off the product	38
To charge the battery	38
To adjust the cutting height with Automower® Access	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
To clean the blade disc	40
Chassis	41
Wheels	41
The body of the product	41
Charging station	41
Replace the blades	41
To replace the blades	41
To replace the top covers	42
To remove the front top cover	42
To install the front top cover	42
To remove the rear top cover	43
To install the rear top cover	44
Battery	44
Winter service	45
Troubleshooting	46
Introduction - troubleshooting	46
Error icons in the Automower® Access display	46
Fault messages	47
Information messages	54
Indicator lamp in the charging station	55
Symptoms	56
Find breaks in the loop wire	57
Transportation, storage and disposal	60
Transportation	60
Storage	60
Disposal	60
To remove the battery	60
Technical data	62
Technical data	62
Registered trademarks	64
Warranty	65
Warranty terms	65
Applicable to US/CA market	66
Supplier's Declaration of Conformity	66

Husqvarna AUTOMOWER 435X AWD Owner Manual - Page 32

Operation, Weather timer, To set the Weather timer, ECO mode, To set the ECO mode, Installation - garage

Page 32 highlights