Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 435X AWD » Manual Viewer

Husqvarna AUTOMOWER 435X AWD Owner Manual - Page 50

Alarm! Mower was, Alarm! Outside ge

View all Husqvarna AUTOMOWER 435X AWD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Message Cause Action Charging station blocked The contact between the charging strips and contact strips may be poor and the product has made a number of attempts to charge. Put the product in the charging station and check that the charging strips and contact strips make good contact. Clean the contact and charging plates. Stuck in charging station An object causes a blockage and the product cannot enter the charging station. The baseplate is tilted or bent. The product slips on the baseplate. There is an object in the way of the product preventing it from leaving the charging station. Remove the object. Make sure that the baseplate is put on level ground. Clean the baseplate. Remove the object. Upside down The product is leaning too much or has Turn the product the right way up. turned over. Mower tilted The product is tilted more than the maximum angle. Move the product to a flat area. Lifted A blockage has activated the lift senors Remove the product from the blockage. and caused the product to stop. If the problem remains it requires action by authorized service technician. Collision sensor problem The product body can not move freely Make sure that the product body can around its chassis. move freely around its chassis. If the problem remains, the message requires action by authorized service technician. Slope too steep Mower stopped because the slope is too steep. Change the installation of the boundary wire to exclude this steep part of the work area. Refer to To examine where to put the boundary wire on page 21. Alarm! Mower switched off Alarm! Mower stopped The alarm was activated because the product was switched OFF. The alarm was activated because the product was stopped. Adjust the security level in the Security menu, refer to Security (Bluetooth® on- ly) on page 35. Alarm! Mower was The alarm was activated because the moved product was moved. Alarm! Outside ge- The alarm was activated because the ofence mower was outside its GeoFence. Adjust the theft protection area (GeoFence) in the Automower Connect menu. 50 - Troubleshooting 1404 - 002 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Access	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the battery	6
General manual instructions	6
Automower® Access	6
Display	7
To operate Automower® Access	8
Menu structure overview in Automower® Access	9
Menu structure overview 1	11
Menu structure overview 2	12
Menu structure overview 3	13
LED status indicator	14
Safety	15
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	15
Safety definitions	16
Safety instructions for operation	16
Use	16
Battery safety	17
How to lift and move the product	18
Maintenance	18
In the event of a thunderstorm	19
Installation	20
Introduction - Installation	20
Main components for installation	20
General preparations	20
Before the installation of the wires	20
To examine where to put the charging station	20
To examine where to put the power supply	21
To examine where to put the boundary wire	21
To put the boundary wire in a slope	23
Passages	23
To make an island	23
To make a secondary area	24
To examine where to put the guide wire	25
Work area examples	25
Installation of the product	25
Installation tools	25
To install the charging station	26
To install the boundary wire	27
To install the guide wire	27
To put the wire into position with stakes	28
To bury the boundary wire or the guide wire	28
To extend the boundary wire or the guide wire	28
After the installation of the product	29
To do a visual check of the charging station	29
Automower® Connect	29
To install the Automower® Connect app	29
To pair Automower® Connect and the product	29
My mowers	29
Firmware over the air (FOTA)	29
To set the Firmware over the air (FOTA)	29
Automower® Direct	29
To start to use Automower® Direct	30
User interface overview	30
To start the product for the first time	30
Settings in Automower® Connect	31
Schedule	31
To edit the schedule settings	31
To add a new schedule setting	31
To calculate the schedule setting	31
Operation	32
Weather timer	32
To set the Weather timer	32
ECO mode	32
To set the ECO mode	32
Installation	32
To find the charging station	32
To change the signal range of the charging station	33
To set the delay time for the guide wire and the boundary wire	33
Lawn coverage	33
To set the GPS function	33
To set the Lawn Coverage function	33
To measure the distance from the charging station	34
To do a test of the Lawn Coverage function	34
Drive Past Wire	34
To set the Drive past wire	34
Starting point	34
To set the starting point	34
Accessories	34
Headlights	34
To set the headlight settings	34
To set the headlight to flash when fault	34
To avoid collisions with the mower house	35
General (Bluetooth® only)	35
Time & date	35
To set the time & date	35
Reset to factory settings	35
To reset to factory settings	35
Security (Bluetooth® only)	35
New loop signal	35
To create a New loop signal	35
To change the PIN code	35
Theft protection	35
Require PIN code	35
Alarm duration	35
STOP button pressed	35
Carried away	36
To set the Theft protection	36
GeoFence	36
To set the center position for the GeoFence function	36
Automower® Connect (Bluetooth® only)	36
Messages	36
Operation	37
To switch on the product	37
Operating modes	37
Main area	37
Secondary area (2nd area)	37
Park	37
Park until further notice	38
Park for a selected number of hours	38
To stop the product	38
To switch off the product	38
To charge the battery	38
To adjust the cutting height with Automower® Access	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
To clean the blade disc	40
Chassis	41
Wheels	41
The body of the product	41
Charging station	41
Replace the blades	41
To replace the blades	41
To replace the top covers	42
To remove the front top cover	42
To install the front top cover	42
To remove the rear top cover	43
To install the rear top cover	44
Battery	44
Winter service	45
Troubleshooting	46
Introduction - troubleshooting	46
Error icons in the Automower® Access display	46
Fault messages	47
Information messages	54
Indicator lamp in the charging station	55
Symptoms	56
Find breaks in the loop wire	57
Transportation, storage and disposal	60
Transportation	60
Storage	60
Disposal	60
To remove the battery	60
Technical data	62
Technical data	62
Registered trademarks	64
Warranty	65
Warranty terms	65
Applicable to US/CA market	66
Supplier's Declaration of Conformity	66

Match case Limit results 1 per page

Message

Cause

Action

Charging station

blocked

The contact between the charging

strips and contact strips may be poor

and the product has made a number of

attempts to charge.

Put the product in the charging station

and check that the charging strips and

contact strips make good contact.

Clean the contact and charging plates.

An object causes a blockage and the

product cannot enter the charging sta-

tion.

Remove the object.

The baseplate is tilted or bent.

Make sure that the baseplate is put on

level ground.

Stuck in charging

station

The product slips on the baseplate.

Clean the baseplate.

There is an object in the way of the

product preventing it from leaving the

charging station.

Remove the object.

Upside down

The product is leaning too much or has

turned over.

Turn the product the right way up.

Mower tilted

The product is tilted more than the

maximum angle.

Move the product to a flat area.

Lifted

A blockage has activated the lift senors

and caused the product to stop.

Remove the product from the blockage.

If the problem remains it requires action

by authorized service technician.

Collision sensor

problem

The product body can not move freely

around its chassis.

Make sure that the product body can

move freely around its chassis.

If the problem remains, the message

requires action by authorized service

technician.

Slope too steep

Mower stopped because the slope is

too steep.

Change the installation of the boundary

wire to exclude this steep part of the

work area. Refer to

To examine where

to put the boundary wire on page 21

Alarm! Mower

switched off

The alarm was activated because the

product was switched OFF.

Adjust the security level in the

Security

menu, refer to

Security (Bluetooth

on-

ly) on page 35

Alarm! Mower

stopped

The alarm was activated because the

product was stopped.

Alarm! Mower was

moved

The alarm was activated because the

product was moved.

Alarm! Outside ge-

ofence

The alarm was activated because the

mower was outside its GeoFence.

Adjust the theft protection area (Geo-

Fence) in the

Automower Connect

menu.

- Troubleshooting

1404 - 002 -