Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 435X AWD » Manual Viewer

Husqvarna AUTOMOWER 435X AWD Owner Manual - Page 56

Symptoms, To install the charging

View all Husqvarna AUTOMOWER 435X AWD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

6.6 Symptoms If your product does not work as expected, follow the symptoms guide below. There is a FAQ (Frequently Asked Questions) on www.husqvarna.com which provides more detailed answers to a number of standard questions. Contact your local Husqvarna representative if you still cannot find the reason for the fault. Symptoms Cause Action The product has difficulty docking. The boundary wire is not laid in a long straight line that is far enough out from the charging station. Check that the charging station has been installed according to the instructions. Refer to To install the charging station on page 26 The charging station is on a slope. Place the charging station on a surface that is entirely level. Refer to To examine where to put the charging station on page 20. The product runs The clock needs to be set. at the wrong time. Set the clock. Refer to Time & date on page 35. The start and stop times for mowing are incorrect. Reset the start time and change the Schedule settings. Refer to Schedule on page 31. The product vibrates. Damaged blades lead to imbalance in the cutting system. Inspect the blades and screws and replace them if necessary. Refer to Replace the blades on page 41. Too many blades in the same position Check that only one blade is fitted at lead to imbalance in the cutting system. each screw. Different versions (thickness) of Husq- Check if the blades are of different ver- varna blades are used. sions. The product runs, but the blade disc does not rotate. The product searches for the charging station. No action. The blade disc does not rotate when the product is searching for the charging station. The product mows for shorter periods than usual between charges. Grass or other foreign object blocks the blade disc. The battery is spent. Remove and clean the blade disc. Refer to Replace the blades on page 41. Replace the battery. Refer to Battery on page 44. Both the mowing The battery is spent. and charging times are shorter than usual. Replace the battery. Refer to Battery on page 44. 56 - Troubleshooting 1404 - 002 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Access	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the battery	6
General manual instructions	6
Automower® Access	6
Display	7
To operate Automower® Access	8
Menu structure overview in Automower® Access	9
Menu structure overview 1	11
Menu structure overview 2	12
Menu structure overview 3	13
LED status indicator	14
Safety	15
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	15
Safety definitions	16
Safety instructions for operation	16
Use	16
Battery safety	17
How to lift and move the product	18
Maintenance	18
In the event of a thunderstorm	19
Installation	20
Introduction - Installation	20
Main components for installation	20
General preparations	20
Before the installation of the wires	20
To examine where to put the charging station	20
To examine where to put the power supply	21
To examine where to put the boundary wire	21
To put the boundary wire in a slope	23
Passages	23
To make an island	23
To make a secondary area	24
To examine where to put the guide wire	25
Work area examples	25
Installation of the product	25
Installation tools	25
To install the charging station	26
To install the boundary wire	27
To install the guide wire	27
To put the wire into position with stakes	28
To bury the boundary wire or the guide wire	28
To extend the boundary wire or the guide wire	28
After the installation of the product	29
To do a visual check of the charging station	29
Automower® Connect	29
To install the Automower® Connect app	29
To pair Automower® Connect and the product	29
My mowers	29
Firmware over the air (FOTA)	29
To set the Firmware over the air (FOTA)	29
Automower® Direct	29
To start to use Automower® Direct	30
User interface overview	30
To start the product for the first time	30
Settings in Automower® Connect	31
Schedule	31
To edit the schedule settings	31
To add a new schedule setting	31
To calculate the schedule setting	31
Operation	32
Weather timer	32
To set the Weather timer	32
ECO mode	32
To set the ECO mode	32
Installation	32
To find the charging station	32
To change the signal range of the charging station	33
To set the delay time for the guide wire and the boundary wire	33
Lawn coverage	33
To set the GPS function	33
To set the Lawn Coverage function	33
To measure the distance from the charging station	34
To do a test of the Lawn Coverage function	34
Drive Past Wire	34
To set the Drive past wire	34
Starting point	34
To set the starting point	34
Accessories	34
Headlights	34
To set the headlight settings	34
To set the headlight to flash when fault	34
To avoid collisions with the mower house	35
General (Bluetooth® only)	35
Time & date	35
To set the time & date	35
Reset to factory settings	35
To reset to factory settings	35
Security (Bluetooth® only)	35
New loop signal	35
To create a New loop signal	35
To change the PIN code	35
Theft protection	35
Require PIN code	35
Alarm duration	35
STOP button pressed	35
Carried away	36
To set the Theft protection	36
GeoFence	36
To set the center position for the GeoFence function	36
Automower® Connect (Bluetooth® only)	36
Messages	36
Operation	37
To switch on the product	37
Operating modes	37
Main area	37
Secondary area (2nd area)	37
Park	37
Park until further notice	38
Park for a selected number of hours	38
To stop the product	38
To switch off the product	38
To charge the battery	38
To adjust the cutting height with Automower® Access	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
To clean the blade disc	40
Chassis	41
Wheels	41
The body of the product	41
Charging station	41
Replace the blades	41
To replace the blades	41
To replace the top covers	42
To remove the front top cover	42
To install the front top cover	42
To remove the rear top cover	43
To install the rear top cover	44
Battery	44
Winter service	45
Troubleshooting	46
Introduction - troubleshooting	46
Error icons in the Automower® Access display	46
Fault messages	47
Information messages	54
Indicator lamp in the charging station	55
Symptoms	56
Find breaks in the loop wire	57
Transportation, storage and disposal	60
Transportation	60
Storage	60
Disposal	60
To remove the battery	60
Technical data	62
Technical data	62
Registered trademarks	64
Warranty	65
Warranty terms	65
Applicable to US/CA market	66
Supplier's Declaration of Conformity	66

Match case Limit results 1 per page

6.6 Symptoms

If your product does not work as expected, follow the symptoms guide below.

There is a FAQ (Frequently Asked Questions) on www.husqvarna.com which provides more detailed

answers to a number of standard questions. Contact your local Husqvarna representative if you still

cannot find the reason for the fault.

Symptoms

Cause

Action

The product has

difficulty docking.

The boundary wire is not laid in a long

straight line that is far enough out from

the charging station.

Check that the charging station has

been installed according to the instruc-

tions. Refer to

To install the charging

station on page 26

The charging station is on a slope.

Place the charging station on a surface

that is entirely level. Refer to

To exam-

ine where to put the charging station on

page 20

The product runs

at the wrong time.

The clock needs to be set.

Set the clock. Refer to

Time & date on

page 35

The start and stop times for mowing

are incorrect.

Reset the start time and change the

Schedule

settings. Refer to

Schedule

on page 31

The product vi-

brates.

Damaged blades lead to imbalance in

the cutting system.

Inspect the blades and screws and re-

place them if necessary. Refer to

Re-

place the blades on page 41

Too many blades in the same position

lead to imbalance in the cutting system.

Check that only one blade is fitted at

each screw.

Different versions (thickness) of Husq-

varna blades are used.

Check if the blades are of different ver-

sions.

The product runs,

but the blade disc

does not rotate.

The product searches for the charging

station.

No action. The blade disc does not ro-

tate when the product is searching for

the charging station.

The product mows

for shorter periods

than usual be-

tween charges.

Grass or other foreign object blocks the

blade disc.

Remove and clean the blade disc. Re-

fer to

Replace the blades on page 41

The battery is spent.

Replace the battery. Refer to

Battery

on page 44

Both the mowing

and charging times

are shorter than

usual.

The battery is spent.

Replace the battery. Refer to

Battery

on page 44

- Troubleshooting

1404 - 002 -