Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 435X AWD » Manual Viewer

Husqvarna AUTOMOWER 435X AWD Owner Manual - Page 54

Information messages, Connection

View all Husqvarna AUTOMOWER 435X AWD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

6.4 Information messages The table below shows a number of information messages that may be shown in Automower® Connect. Contact your local Husqvarna representative if the same message appears often. For more information, refer to Messages on page 36. Message Low battery Cause The product cannot find the charging station. Action Change the position of the guide wire. Refer to To install the guide wire on page 27. Make sure that the charging station is installed correctly. Refer to To find the charging station on page 32. The battery is spent. Replace the battery. Refer to Battery on page 44. The charging station's antenna is defective. Check if the indicator lamp in the charging station flashes red. Refer to Indicator lamp in the charging station on page 55. This problem requires action by authorized service technician. Settings restored Confirmation that Reset all user settings has been carried out. This is normal. No action required. Guide 1/2 not found The guide wire is not connected to the charging station. Check that the guide wire's connector is tightly connected to the charging station. Refer to To install the guide wire on page 27. Break in the guide wire. Find out where the break is. Replace the damaged section of the guide wire with a new loop wire and splice using an original coupler. The guide wire is not connected to the boundary loop. Check that the guide wire is connected correctly to the boundary loop. Refer to To install the guide wire on page 27. Connection changed New loop signal successfully changed. No action. Connection NOT Failed to change the loop signal. changed Create a new loop signal, try several times. If the problem remains, the message requires action by authorized service technician. Refer to To create a New loop signal on page 35. Slope too steep The product stopped mowing because the slope is too steep. If this problem occurs frequently, change the installation of the boundary wire to exclude the steep part of the work area. 54 - Troubleshooting 1404 - 002 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Access	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the battery	6
General manual instructions	6
Automower® Access	6
Display	7
To operate Automower® Access	8
Menu structure overview in Automower® Access	9
Menu structure overview 1	11
Menu structure overview 2	12
Menu structure overview 3	13
LED status indicator	14
Safety	15
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	15
Safety definitions	16
Safety instructions for operation	16
Use	16
Battery safety	17
How to lift and move the product	18
Maintenance	18
In the event of a thunderstorm	19
Installation	20
Introduction - Installation	20
Main components for installation	20
General preparations	20
Before the installation of the wires	20
To examine where to put the charging station	20
To examine where to put the power supply	21
To examine where to put the boundary wire	21
To put the boundary wire in a slope	23
Passages	23
To make an island	23
To make a secondary area	24
To examine where to put the guide wire	25
Work area examples	25
Installation of the product	25
Installation tools	25
To install the charging station	26
To install the boundary wire	27
To install the guide wire	27
To put the wire into position with stakes	28
To bury the boundary wire or the guide wire	28
To extend the boundary wire or the guide wire	28
After the installation of the product	29
To do a visual check of the charging station	29
Automower® Connect	29
To install the Automower® Connect app	29
To pair Automower® Connect and the product	29
My mowers	29
Firmware over the air (FOTA)	29
To set the Firmware over the air (FOTA)	29
Automower® Direct	29
To start to use Automower® Direct	30
User interface overview	30
To start the product for the first time	30
Settings in Automower® Connect	31
Schedule	31
To edit the schedule settings	31
To add a new schedule setting	31
To calculate the schedule setting	31
Operation	32
Weather timer	32
To set the Weather timer	32
ECO mode	32
To set the ECO mode	32
Installation	32
To find the charging station	32
To change the signal range of the charging station	33
To set the delay time for the guide wire and the boundary wire	33
Lawn coverage	33
To set the GPS function	33
To set the Lawn Coverage function	33
To measure the distance from the charging station	34
To do a test of the Lawn Coverage function	34
Drive Past Wire	34
To set the Drive past wire	34
Starting point	34
To set the starting point	34
Accessories	34
Headlights	34
To set the headlight settings	34
To set the headlight to flash when fault	34
To avoid collisions with the mower house	35
General (Bluetooth® only)	35
Time & date	35
To set the time & date	35
Reset to factory settings	35
To reset to factory settings	35
Security (Bluetooth® only)	35
New loop signal	35
To create a New loop signal	35
To change the PIN code	35
Theft protection	35
Require PIN code	35
Alarm duration	35
STOP button pressed	35
Carried away	36
To set the Theft protection	36
GeoFence	36
To set the center position for the GeoFence function	36
Automower® Connect (Bluetooth® only)	36
Messages	36
Operation	37
To switch on the product	37
Operating modes	37
Main area	37
Secondary area (2nd area)	37
Park	37
Park until further notice	38
Park for a selected number of hours	38
To stop the product	38
To switch off the product	38
To charge the battery	38
To adjust the cutting height with Automower® Access	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
To clean the blade disc	40
Chassis	41
Wheels	41
The body of the product	41
Charging station	41
Replace the blades	41
To replace the blades	41
To replace the top covers	42
To remove the front top cover	42
To install the front top cover	42
To remove the rear top cover	43
To install the rear top cover	44
Battery	44
Winter service	45
Troubleshooting	46
Introduction - troubleshooting	46
Error icons in the Automower® Access display	46
Fault messages	47
Information messages	54
Indicator lamp in the charging station	55
Symptoms	56
Find breaks in the loop wire	57
Transportation, storage and disposal	60
Transportation	60
Storage	60
Disposal	60
To remove the battery	60
Technical data	62
Technical data	62
Registered trademarks	64
Warranty	65
Warranty terms	65
Applicable to US/CA market	66
Supplier's Declaration of Conformity	66