Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 435X AWD » Manual Viewer

Husqvarna AUTOMOWER 435X AWD Owner Manual - Page 48

Find breaks in the, loop wire

View all Husqvarna AUTOMOWER 435X AWD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

confirmed in Automower® Access display on the product. Contact your local Husqvarna representative if the same message appears often. For more information, refer to Messages on page 36. Message No loop signal Cause Action The power supply or the voltage cable are not connected. Examine the LED status on the charging station. If the LED is not lit, it indicates that there is no power. Examine the wall socket connection and whether an earth-fault breaker has tripped. Make sure that the low voltage cable is connected to the charging station. Wheel motor blocked Wheel drive problem The power supply or low voltage cable Replace the power supply or low volt- are damaged. age cable. The boundary wire is not connected to the charging station. Make sure that the boundary wire connectors are fitted properly to the charging station. Replace connectors if damaged. Refer to To install the boundary wire on page 27. The boundary wire is broken. Check the signal given by the LED on the charging station. If the LED indicates break in the boundary wire, find out where the break is. Replace the damaged section of the loop with a new loop wire and splice using an original coupler. Refer to Find breaks in the loop wire on page 57. ECO mode is activated and the product has attempted to start outside the charging station. Put the product in the charging station. Start the product and close the hatch. The pairing between the product and the charging station is lost. Put the product in the charging station and generate a new loop signal. Refer to To create a New loop signal on page 35. The boundary wire is crossed on its way to and from an island. Make sure that the boundary wire is installed correctly. Refer to To install the boundary wire on page 27. Disturbances from metal objects (fen- Move the boundary wire and/or make ces, reinforcement steel) or buried ca- more islands in the work area to in- bles. crease the signal strength. Grass or other object has wrapped around the drive wheel. Examine the drive wheel and remove the grass or other object. 48 - Troubleshooting 1404 - 002 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Access	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the battery	6
General manual instructions	6
Automower® Access	6
Display	7
To operate Automower® Access	8
Menu structure overview in Automower® Access	9
Menu structure overview 1	11
Menu structure overview 2	12
Menu structure overview 3	13
LED status indicator	14
Safety	15
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	15
Safety definitions	16
Safety instructions for operation	16
Use	16
Battery safety	17
How to lift and move the product	18
Maintenance	18
In the event of a thunderstorm	19
Installation	20
Introduction - Installation	20
Main components for installation	20
General preparations	20
Before the installation of the wires	20
To examine where to put the charging station	20
To examine where to put the power supply	21
To examine where to put the boundary wire	21
To put the boundary wire in a slope	23
Passages	23
To make an island	23
To make a secondary area	24
To examine where to put the guide wire	25
Work area examples	25
Installation of the product	25
Installation tools	25
To install the charging station	26
To install the boundary wire	27
To install the guide wire	27
To put the wire into position with stakes	28
To bury the boundary wire or the guide wire	28
To extend the boundary wire or the guide wire	28
After the installation of the product	29
To do a visual check of the charging station	29
Automower® Connect	29
To install the Automower® Connect app	29
To pair Automower® Connect and the product	29
My mowers	29
Firmware over the air (FOTA)	29
To set the Firmware over the air (FOTA)	29
Automower® Direct	29
To start to use Automower® Direct	30
User interface overview	30
To start the product for the first time	30
Settings in Automower® Connect	31
Schedule	31
To edit the schedule settings	31
To add a new schedule setting	31
To calculate the schedule setting	31
Operation	32
Weather timer	32
To set the Weather timer	32
ECO mode	32
To set the ECO mode	32
Installation	32
To find the charging station	32
To change the signal range of the charging station	33
To set the delay time for the guide wire and the boundary wire	33
Lawn coverage	33
To set the GPS function	33
To set the Lawn Coverage function	33
To measure the distance from the charging station	34
To do a test of the Lawn Coverage function	34
Drive Past Wire	34
To set the Drive past wire	34
Starting point	34
To set the starting point	34
Accessories	34
Headlights	34
To set the headlight settings	34
To set the headlight to flash when fault	34
To avoid collisions with the mower house	35
General (Bluetooth® only)	35
Time & date	35
To set the time & date	35
Reset to factory settings	35
To reset to factory settings	35
Security (Bluetooth® only)	35
New loop signal	35
To create a New loop signal	35
To change the PIN code	35
Theft protection	35
Require PIN code	35
Alarm duration	35
STOP button pressed	35
Carried away	36
To set the Theft protection	36
GeoFence	36
To set the center position for the GeoFence function	36
Automower® Connect (Bluetooth® only)	36
Messages	36
Operation	37
To switch on the product	37
Operating modes	37
Main area	37
Secondary area (2nd area)	37
Park	37
Park until further notice	38
Park for a selected number of hours	38
To stop the product	38
To switch off the product	38
To charge the battery	38
To adjust the cutting height with Automower® Access	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
To clean the blade disc	40
Chassis	41
Wheels	41
The body of the product	41
Charging station	41
Replace the blades	41
To replace the blades	41
To replace the top covers	42
To remove the front top cover	42
To install the front top cover	42
To remove the rear top cover	43
To install the rear top cover	44
Battery	44
Winter service	45
Troubleshooting	46
Introduction - troubleshooting	46
Error icons in the Automower® Access display	46
Fault messages	47
Information messages	54
Indicator lamp in the charging station	55
Symptoms	56
Find breaks in the loop wire	57
Transportation, storage and disposal	60
Transportation	60
Storage	60
Disposal	60
To remove the battery	60
Technical data	62
Technical data	62
Registered trademarks	64
Warranty	65
Warranty terms	65
Applicable to US/CA market	66
Supplier's Declaration of Conformity	66

Match case Limit results 1 per page

confirmed in Automower

Access display on the product. Contact your local Husqvarna representative

if the same message appears often. For more information, refer to

Messages on page 36

Message

Cause

Action

No loop signal

The power supply or the voltage cable

are not connected.

Examine the LED status on the charg-

ing station. If the LED is not lit, it indi-

cates that there is no power. Examine

the wall socket connection and whether

an earth-fault breaker has tripped.

Make sure that the low voltage cable is

connected to the charging station.

The power supply or low voltage cable

are damaged.

Replace the power supply or low volt-

age cable.

The boundary wire is not connected to

the charging station.

Make sure that the boundary wire con-

nectors are fitted properly to the charg-

ing station. Replace connectors if dam-

aged. Refer to

To install the boundary

wire on page 27

The boundary wire is broken.

Check the signal given by the LED on

the charging station. If the LED indi-

cates break in the boundary wire, find

out where the break is. Replace the

damaged section of the loop with a new

loop wire and splice using an original

coupler. Refer to

Find breaks in the

loop wire on page 57

ECO mode

is activated and the prod-

uct has attempted to start outside the

charging station.

Put the product in the charging station.

Start the product and close the hatch.

The pairing between the product and

the charging station is lost.

Put the product in the charging station

and generate a new loop signal. Refer

To create a New loop signal on page

The boundary wire is crossed on its

way to and from an island.

Make sure that the boundary wire is in-

stalled correctly. Refer to

To install the

boundary wire on page 27

Disturbances from metal objects (fen-

ces, reinforcement steel) or buried ca-

bles.

Move the boundary wire and/or make

more islands in the work area to in-

crease the signal strength.

Wheel motor

blocked

Grass or other object has wrapped

around the drive wheel.

Examine the drive wheel and remove

the grass or other object.

Wheel drive prob-

lem

- Troubleshooting

1404 - 002 -