Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 435X AWD » Manual Viewer

Husqvarna AUTOMOWER 435X AWD Owner Manual - Page 37

Operation, To switch on the product, Operating modes, Main area, Secondary area (2nd area), Park

View all Husqvarna AUTOMOWER 435X AWD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

4 Operation 4.1 To switch on the product WARNING: Read and understand the safety chapter before you switch on the product. WARNING: Keep your hands and feet away from the rotating blades. Do not put your hands or feet near or below the product when the motor is running. WARNING: Do not use the product when persons, especially children, or animals, are in the work area. 1. Push the jog wheel for 3 seconds to switch on the product. 3 sec Note: Make sure that the STOP button is pushed down. If the STOP button is not pushed down a STOP symbol will show on the display. 2. Use the jog wheel to enter the PIN code. The correct PIN code must be entered to get access to the menu. If the incorrect PIN code is entered 5 times, the product is locked for a time. The lock is extended for each new incorrect try. 3. Select the desired operating mode and push the jog wheel. Refer to Operating modes on page 37. 4. Push the START button to start the product. If the product is parked in the charging station, it will only leave the charging station when the battery is fully charged and if the Schedule is set to let the product operate. 4.2 Operating modes In the Automower® Access menu the following operation modes can be selected: • Main area • Secondary area • Park 4.2.1 Main area Main area is the standard operating mode where the product mows and charges automatically. 4.2.2 Secondary area (2nd area) To mow secondary areas the operating mode Secondary area (2nd area) must be selected. In this mode, the operator must move the product manually between the main area and the secondary area. The product mows for a selected period of time or until the battery is empty. 4.2.3 Park When the Park mode is selected the following operation selections can be chosen: • Park until further notice • Park for a specific number of hours Refer to Menu structure overview in Automower® Access on page 9. 1404 - 002 - Operation - 37

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Access	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the battery	6
General manual instructions	6
Automower® Access	6
Display	7
To operate Automower® Access	8
Menu structure overview in Automower® Access	9
Menu structure overview 1	11
Menu structure overview 2	12
Menu structure overview 3	13
LED status indicator	14
Safety	15
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	15
Safety definitions	16
Safety instructions for operation	16
Use	16
Battery safety	17
How to lift and move the product	18
Maintenance	18
In the event of a thunderstorm	19
Installation	20
Introduction - Installation	20
Main components for installation	20
General preparations	20
Before the installation of the wires	20
To examine where to put the charging station	20
To examine where to put the power supply	21
To examine where to put the boundary wire	21
To put the boundary wire in a slope	23
Passages	23
To make an island	23
To make a secondary area	24
To examine where to put the guide wire	25
Work area examples	25
Installation of the product	25
Installation tools	25
To install the charging station	26
To install the boundary wire	27
To install the guide wire	27
To put the wire into position with stakes	28
To bury the boundary wire or the guide wire	28
To extend the boundary wire or the guide wire	28
After the installation of the product	29
To do a visual check of the charging station	29
Automower® Connect	29
To install the Automower® Connect app	29
To pair Automower® Connect and the product	29
My mowers	29
Firmware over the air (FOTA)	29
To set the Firmware over the air (FOTA)	29
Automower® Direct	29
To start to use Automower® Direct	30
User interface overview	30
To start the product for the first time	30
Settings in Automower® Connect	31
Schedule	31
To edit the schedule settings	31
To add a new schedule setting	31
To calculate the schedule setting	31
Operation	32
Weather timer	32
To set the Weather timer	32
ECO mode	32
To set the ECO mode	32
Installation	32
To find the charging station	32
To change the signal range of the charging station	33
To set the delay time for the guide wire and the boundary wire	33
Lawn coverage	33
To set the GPS function	33
To set the Lawn Coverage function	33
To measure the distance from the charging station	34
To do a test of the Lawn Coverage function	34
Drive Past Wire	34
To set the Drive past wire	34
Starting point	34
To set the starting point	34
Accessories	34
Headlights	34
To set the headlight settings	34
To set the headlight to flash when fault	34
To avoid collisions with the mower house	35
General (Bluetooth® only)	35
Time & date	35
To set the time & date	35
Reset to factory settings	35
To reset to factory settings	35
Security (Bluetooth® only)	35
New loop signal	35
To create a New loop signal	35
To change the PIN code	35
Theft protection	35
Require PIN code	35
Alarm duration	35
STOP button pressed	35
Carried away	36
To set the Theft protection	36
GeoFence	36
To set the center position for the GeoFence function	36
Automower® Connect (Bluetooth® only)	36
Messages	36
Operation	37
To switch on the product	37
Operating modes	37
Main area	37
Secondary area (2nd area)	37
Park	37
Park until further notice	38
Park for a selected number of hours	38
To stop the product	38
To switch off the product	38
To charge the battery	38
To adjust the cutting height with Automower® Access	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
To clean the blade disc	40
Chassis	41
Wheels	41
The body of the product	41
Charging station	41
Replace the blades	41
To replace the blades	41
To replace the top covers	42
To remove the front top cover	42
To install the front top cover	42
To remove the rear top cover	43
To install the rear top cover	44
Battery	44
Winter service	45
Troubleshooting	46
Introduction - troubleshooting	46
Error icons in the Automower® Access display	46
Fault messages	47
Information messages	54
Indicator lamp in the charging station	55
Symptoms	56
Find breaks in the loop wire	57
Transportation, storage and disposal	60
Transportation	60
Storage	60
Disposal	60
To remove the battery	60
Technical data	62
Technical data	62
Registered trademarks	64
Warranty	65
Warranty terms	65
Applicable to US/CA market	66
Supplier's Declaration of Conformity	66

Match case Limit results 1 per page

4 Operation

4.1 To switch on the product

WARNING:

Read and understand the

safety chapter before you switch on

the product.

WARNING:

Keep your hands and feet

away from the rotating blades. Do not

put your hands or feet near or below

the product when the motor is running.

WARNING:

Do not use the product

when persons, especially children, or

animals, are in the work area.

Push the

jog wheel

for 3 seconds to switch

on the product.

3 sec

Note:

Make sure that the

STOP

button is

pushed down. If the

STOP

button is not

pushed down a

STOP

symbol will show on

the display.

Use the

jog wheel

to enter the PIN code.

The correct PIN code must be entered to get

access to the menu. If the incorrect PIN

code is entered 5 times, the product is

locked for a time. The lock is extended for

each new incorrect try.

Select the desired operating mode and push

the

jog wheel

. Refer to

Operating modes on

page 37

Push the

START

button to start the product.

If the product is parked in the charging

station, it will only leave the charging station

when the battery is fully charged and if the

Schedule

is set to let the product operate.

4.2 Operating modes

In the Automower

Access menu the following

operation modes can be selected:

•

Main area

•

Secondary area

•

Park

4.2.1 Main area

Main area

is the standard operating mode where

the product mows and charges automatically.

4.2.2 Secondary area (2nd area)

To mow secondary areas the operating mode

Secondary area (2nd area)

must be selected. In

this mode, the operator must move the product

manually between the main area and the

secondary area. The product mows for a selected

period of time or until the battery is empty.

4.2.3 Park

When the

Park

mode is selected the following

operation selections can be chosen:

•

Park until further notice

•

Park for a specific number of hours

Refer to

Menu structure overview in Automower

Access on page 9

1404 - 002 -

Operation -