IBM 6400 Operation Guide - Page 102

service representative.

Get IBM 6400 - Model 008 B/W Line-matrix Printer PDF manuals and user guides View all IBM 6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

status and fault messages 065 HAMMER BANK FAN FAULT 069 DATA CLEARED 080 POWER SUPPLY HOT 082 POWER SUPPLY 8.5V FAILED 083 INTAKE FAN FAULT 084 POWER SUPPLY 48V FAILED 085 CONTROLLER VOLTAGE 086 CONTROLLER 15V 087 PLATEN OPEN TIMEOUT CLOSE PLATEN Sensors cannot detect current in fan circuit. Refer to the Setup Guide for correction procedure. Appears when data is cleared out of printer after Cancel key has been pressed. No action necessary. Circuits are overheating on the power supply board. Contact an IBM service representative. Internal power failure. Contact an IBM service representative. Sensors cannot detect current in fan circuit. Refer to the Setup Guide for correction procedure. Internal power failure. Contact an IBM service representative. Controller voltage failure. Contact an IBM service representative. Controller voltage failure. Contact an IBM service representative. Indicates the forms thickness lever has been open for at least one minute. The Intervention Required parameter is set to Send to Host. Close forms thickness lever. 88 Operator's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
status and fault messages
88
Operator’
s Guide
Sensors cannot detect current in fan
circuit. Refer to the
Setup Guide
for
correction procedure.
Appears when data is cleared out of
printer after
Cancel
key has been
pressed. No action necessary.
Circuits are overheating on the power
supply board. Contact an IBM service
representative.
Internal power failure. Contact an IBM
service representative.
Sensors cannot detect current in fan
circuit. Refer to the
Setup Guide
for
correction procedure.
Internal power failure. Contact an IBM
service representative.
Controller voltage failure. Contact an IBM
service representative.
Controller voltage failure. Contact an IBM
service representative.
Indicates the forms thickness lever has
been open for at least one minute. The
Intervention Required parameter is set to
Send to Host. Close forms thickness
lever.
065
HAMMER BANK F
AN F
AULT
069 DA
T
A CLEARED
080 POWER SUPPL
Y HOT
082 POWER SUPPL
Y 8.5V F
AILED
083 INT
AKE FAN F
AULT
084 POWER SUPPL
Y 48V F
AILED
085 CONTROLLER VOL
TAGE
085 CONTROLLER VOL
TAGE
086 CONTROLLER 15V
087 PLA
TEN OPEN TIMEOUT
CLOSE PLA
TEN