IBM 6400 Operation Guide - Page 62

Replacing the Ribbon - printer replacement

Get IBM 6400 - Model 008 B/W Line-matrix Printer PDF manuals and user guides View all IBM 6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Replacing the Ribbon For detailed ribbon information, refer to your Setup Guide. When replacing ribbons, use only the ribbons listed below: • IBM General Purpose Ribbon, 60yd, P/N 1040990 • IBM General Purpose Ribbon, 100 yd, P/N 1040995 • IBM High Contrast Ribbon, 60 yd, P/N 1040993 • IBM High Contrast Ribbon, 100 yd, P/N 1040998 Ribbons may be purchased directly from your Lexmark distributor. 1 Press Stop to place the printer in NOT READY state. 2 Open the printer cover. 3 Remove the old ribbon: a. On pedestal models, raise the operator panel. b. Raise the forms thickness lever as far as it will go. note If the Ribbon Fault option is set to "Do Nothing," ribbon usage can only be reset from the operator panel by pressing Enter with New Ribbon XXX% displayed at the RibbonMinder option. If you are using RibbonMinder with the Ribbon Fault option set to "New Ribbon" and are changing the ribbon because the message Ribbon Out of Ink, Change Ribbon is displayed, raising the forms thickness lever as far as it will go will reset the RIBBON OUT OF INK, CHANGE RIBBON fault message. It will also reset the ribbon usage to 100%. Hub Latch 48 Forms Thickness Lever Operator's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Replacing the Ribbon
48
Operator’
s Guide
For detailed ribbon information, refer to your
Setup Guide.
When replacing ribbons, use
only the ribbons listed below:
•
IBM General Purpose Ribbon, 60yd,
P/N 1040990
•
IBM General Purpose Ribbon, 100 yd,
P/N 1040995
•
IBM High Contrast Ribbon, 60 yd,
P/N 1040993
•
IBM High Contrast Ribbon, 100 yd,
P/N 1040998
Ribbons may be purchased directly from your
Lexmark distributor.
1
Press
Stop
to place the printer in
NOT READY state.
2
Open the printer cover.
3
Remove the old ribbon:
a.
On pedestal models, raise the
operator panel.
b.
Raise the forms thickness
lever
as far as it will go.
note
If
the Ribbon Fault option is set to “Do
Nothing,” ribbon usage can only be reset
from the operator panel by pressing
Enter
with New Ribbon XXX% displayed at the
RibbonMinder option. If you are using
RibbonMinder with the Ribbon Fault option
set to “New Ribbon” and are changing the
ribbon because the message Ribbon Out of
Ink, Change Ribbon is displayed, raising
the forms thickness lever as far as it will go
will reset the RIBBON OUT OF INK,
CHANGE RIBBON fault message. It will
also reset the ribbon usage to 100%.
Forms Thickness
Lever
Hub Latch