IBM 6400 Operation Guide - Page 50

END OF FORMS fault - shuttle jam

Get IBM 6400 - Model 008 B/W Line-matrix Printer PDF manuals and user guides View all IBM 6400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

reloading paper 12 Lower the forms thickness lever. Set it to match the paper thickness. Refer to the note on the shuttle cover. note Do not set the forms thickness lever too tightly; excessive friction can cause paper jams and ribbon jams with potential for ribbon damage, smeared ink, or wavy print. A Thin Paper B Medium Paper C Thick Paper 13 Press Cancel to clear the "END OF FORMS" fault message from the message display. 14 Close the printer cover and the cabinet front door, as required. 15 Press Start to place the printer in READY state and resume printing. 16 On cabinet models: Open the rear cabinet door and ensure that the paper folds in the stacker the same way it does in the supply area. 17 Close the rear cabinet door. NOTE: Thin Paper = single sheet Medium Paper = two-part form Thick Paper = six-part form Perform steps 18 through 36 only if you are unable to load the new paper over the existing paper in step 3. 18 Open both tractor doors. 36 Operator's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
reloading paper
36
Operator’
s Guide
12
Lower the forms thickness lever. Set
it to match the paper thickness.
Refer to the note on the shuttle
cover.
note
Do
not set the forms thickness lever too
tightly; excessive friction can cause paper
jams and ribbon jams with potential for
ribbon damage, smeared ink, or wavy print.
13
Press
Cancel
to clear the
“END OF FORMS” fault
message from the message
display.
14
Close the printer cover and the
cabinet front door, as required.
15
Press
Start
to place the printer
in READY state and resume
printing.
16
On cabinet models:
Open the rear cabinet door and
ensure that the paper folds in
the stacker the same way it
does in the supply area.
17
Close the rear cabinet door.
Perform steps 18 through 36 only if you are
unable to load the new paper over the
existing paper in step 3.
18
Open both tractor doors.
A
B
C
Thin
Paper
Medium Paper
Thick Paper
NOTE:
Thin Paper = single sheet
Medium Paper = two–part form
Thick Paper = six–part form