IBM 6862 User Guide - Page 125

Enter, Save Settings, or Right Arrow

Get IBM 6862 - PC 300 PL PDF manuals and user guides
UPC - 087944469841
View all IBM 6862 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

To use the Configuration/Setup Utility program, do the following: a. Select the menu item that is flagged (or that you wish to view) by pressing Up Arrow (↑) or Down Arrow (↓), and then press Enter. b. A new menu specific to the item that you selected appears. Press Left Arrow (←) or Right Arrow (→) to toggle between choices for a menu item. (Note that each menu item has a Help screen. To view the Help screen, select the menu item, and then press F1.) c. When you have finished viewing and changing settings, press Esc to return to the Configuration/Setup Utility menu. d. Before you exit from the program, select Save Settings. e. To exit from the Configuration/Setup Utility, press Esc and follow the instructions on the screen. When you exit from the Configuration/Setup Utility menu, your new settings will be saved and your operating system will start automatically (unless there is an unresolved problem with an IDE device). 6. For more information about what caused an error message to appear and what action to take, refer to the following chart. Problem POST error code or message appears. After more than one beep, application program or operating system appears. Blank screen, unreadable screen, or other unusual response occurs. Go to: "POST message charts" on page 108. "Diagnostic programs" on page 136. "Troubleshooting charts" on page 126. If you are unable to resolve a problem and need assistance, refer to Chapter 8, "Getting help, service, and information" on page 141. Chapter 7. Solving problems 107

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
To use the Configuration/Setup Utility program, do the following:
a.
Select the menu item that is flagged (or that you wish to view) by pressing
Up Arrow (
↑
) or Down Arrow (
↓
), and then press
Enter
.
b.
A new menu specific to the item that you selected appears.
Press Left
Arrow (
←
) or Right Arrow (
→
) to toggle between choices for a menu item.
(Note that each menu item has a Help screen.
To view the Help screen,
select the menu item, and then press
F1
.)
c.
When you have finished viewing and changing settings, press
Esc
to return
to the Configuration/Setup Utility menu.
d.
Before you exit from the program, select
Save Settings
.
e.
To exit from the Configuration/Setup Utility, press
Esc
and follow the
instructions on the screen.
When you exit from the Configuration/Setup
Utility menu, your new settings will be saved and your operating system
will start automatically (unless there is an unresolved problem with an IDE
device).
6.
For more information about what caused an error message to appear and what
action to take, refer to the following chart.
If you are unable to resolve a problem and need assistance, refer to Chapter
8,
“Getting help, service, and information” on page
141.
Problem
Go to:
POST error code or message appears.
“POST message charts” on page
108.
After more than one beep, application program or
operating system appears.
“Diagnostic programs” on page
136.
Blank screen, unreadable screen, or other unusual
response occurs.
“Troubleshooting charts” on page
126.
Chapter 7.
Solving problems
107