IBM 865951Y Hardware Maintenance Manual - Page 112

Preparing the rack enclosure, rails, and attach the template to the rear

Get IBM 865951Y - Netfinity 5000 - 51Y PDF manuals and user guides
UPC - 087944501824
View all IBM 865951Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

Preparing the rack enclosure: In this section, you will use the following parts: Two slide bracket assemblies Two slide rails (fitted to system unit) One cable-management arm Ten long screws (M6 by 16 mm) Ten cage nuts Installation template Attention To ensure cabinet stability, plan the installation of servers in the rack enclosure starting from the bottom. Note This procedure requires two people. To attach the mounting hardware to the rack enclosure: 1. Mark the positions of the slide brackets on the mounting rails on the rack enclosure. a. Position the template on the front mounting rail on the rack enclosure, aligning the holes. Secure the template in place with tape. b. Mark the holes for the slide brackets and cage nuts. If you prefer, mark all the cage nut positions on the rack at this time. c. Carefully remove the tape from the mounting rails, and attach the template to the rear mounting rails. Mark the locations for the slide brackets and cage nuts. Notes 1. You must align the slide brackets correctly, or the installation cannot be completed. 2. The slide rails have four screws each to allow for length adjustment. 2. Install the cage nuts in the marked positions as shown. 3. Attach the slide rail to the left side of the rack enclosure. 104 Netfinity Server HMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
Preparing the rack enclosure:
In this section, you
will use the following parts:
±
Two slide bracket assemblies
±
Two slide rails (fitted to system unit)
±
One cable-management arm
±
Ten long screws (M6 by 16 mm)
±
Ten cage nuts
±
Installation template
Attention
To ensure cabinet stability, plan the installation of
servers in the rack enclosure starting from the bottom.
Note
This procedure requires two people.
To attach the mounting hardware to the rack
enclosure:
1.
Mark the positions of the slide brackets on the
mounting rails on the rack enclosure.
a.
Position the template on the front mounting rail
on the rack enclosure, aligning the holes.
Secure the template in place with tape.
b.
Mark the holes for the slide brackets and cage
nuts.
If you prefer, mark
all
the cage nut
positions on the rack at this time.
c.
Carefully remove the tape from the mounting
rails, and attach the template to the rear
mounting rails.
Mark the locations for the slide
brackets and cage nuts.
Notes
1.
You must align the slide brackets correctly,
or the installation cannot be completed.
2.
The slide rails have four screws each to
allow for length adjustment.
2.
Install the cage nuts in the marked positions as
shown.
3.
Attach the slide rail to the left side of the rack
enclosure.
104
Netfinity Server HMM