IBM 865951Y Hardware Maintenance Manual - Page 45

PCNET IRQ does not match PROTOCOL.INI., PCNET IRQ found

Get IBM 865951Y - Netfinity 5000 - 51Y PDF manuals and user guides
UPC - 087944501824
View all IBM 865951Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

PCNTND-15 Device not found. Explanation: The driver cannot find an Ethernet controller in the server. Action: Verify that the PCI Ethernet device type is set to the default (enabled) position in the Configuration/Setup utility programs (see "PCI bus control" on page 30). If the Ethernet adapter is enabled, go to "Diagnostic test programs" on page 10 to run the diagnostic utility. PCNTND-16 PCI scan specified, device not found. Explanation: The driver cannot locate the Ethernet controller on the PCI bus. Action: Verify that the PCI Ethernet device type is set to the default (enabled) position in the Configuration/Setup utility programs (see "PCI bus control" on page 30). If the Ethernet adapter is enabled, go to "Diagnostic test programs" on page 10 to run the diagnostic utility. PCNTND-21 The adapter failed the checksum test. Explanation: The driver cannot find an Ethernet controller. Action: Verify that the PCI Ethernet device type is set to the default (enabled) position in the Configuration/Setup utility programs (see "PCI bus control" on page 30). If the Ethernet adapter is enabled, go to "Diagnostic test programs" on page 10 to run the diagnostic utility. PCNTND-23 WARNING: PCNET IRQ found = xx Explanation: The interrupt request (IRQ) setting (xx) in the PROTOCOL.INI file does not match the hardware IRQ setting. Action: Remove the IRQ setting from the PROTOCOL.INI file or change the IRQ setting in the PROTOCOL.INI file to match the IRQ setting shown in the PCI Routing selection of the System Information menu in the Configuration/Setup Utility. (See "PCI routing" on page 23.) PCNTND-24 WARNING: PCNET IRQ does not match PROTOCOL.INI. Explanation: The interrupt request (IRQ) setting in the PROTOCOL.INI file does not match the hardware IRQ setting. Action: Remove the IRQ setting from the PROTOCOL.INI file or change the IRQ setting in the PROTOCOL.INI file to match the IRQ setting shown in the PCI Routing selection of the System Information menu in the Configuration/Setup Utility. (See "PCI routing" on page 23.) PCNTND-25 PCI scan specified, PCI bus not found! Explanation: The driver cannot locate the PCI bus on the server. Action: Go to "Diagnostic test programs" on page 10 to run the diagnostic utility. PCNTND-29 WARNING: DMA number is not necessary for PCI device. Explanation: The Ethernet controller does not require a DMA setting. Action: Remove the DMA setting in the PROTOCOL.INI file. PCNTND-33 PCNET device with specified IOBASE is already in use. Explanation: The specified I/O address number is already in use by another Ethernet controller or device. Action: Remove the I/O address setting in the PROTOCOL.INI file. Netfinity 5000 - Type 8659 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
PCNTND-15
Device not found.
Explanation:
The driver cannot find an Ethernet controller in the server.
Action:
Verify that the PCI Ethernet device type is set to the default
(enabled) position in the Configuration/Setup utility programs (see “PCI bus
control” on page
30).
If the Ethernet adapter is enabled, go to “Diagnostic test
programs” on page
10 to run the diagnostic utility.
PCNTND-16
PCI scan specified, device not found.
Explanation:
The driver cannot locate the Ethernet controller on the PCI bus.
Action:
Verify that the PCI Ethernet device type is set to the default
(enabled) position in the Configuration/Setup utility programs (see “PCI bus
control” on page
30).
If the Ethernet adapter is enabled, go to “Diagnostic test
programs” on page
10 to run the diagnostic utility.
PCNTND-21
The adapter failed the checksum test.
Explanation:
The driver cannot find an Ethernet controller.
Action:
Verify that the PCI Ethernet device type is set to the default
(enabled) position in the Configuration/Setup utility programs (see “PCI bus
control” on page
30).
If the Ethernet adapter is enabled, go to “Diagnostic test
programs” on page
10 to run the diagnostic utility.
PCNTND-23
WARNING:
PCNET IRQ found
=
xx
Explanation:
The interrupt request (IRQ) setting (
xx
) in the PROTOCOL.INI
file does not match the hardware IRQ setting.
Action:
Remove the IRQ setting from the PROTOCOL.INI file or change the
IRQ setting in the PROTOCOL.INI file to match the IRQ setting shown in the
PCI Routing
selection of the System Information menu in the
Configuration/Setup Utility.
(See “PCI routing” on page
23.)
PCNTND-24
WARNING:
PCNET IRQ does not match PROTOCOL.INI.
Explanation:
The interrupt request (IRQ) setting in the PROTOCOL.INI file
does not match the hardware IRQ setting.
Action:
Remove the IRQ setting from the PROTOCOL.INI file or change the
IRQ setting in the PROTOCOL.INI file to match the IRQ setting shown in the
PCI Routing
selection of the System Information menu in the
Configuration/Setup Utility.
(See “PCI routing” on page
23.)
PCNTND-25
PCI scan specified, PCI bus not found!
Explanation:
The driver cannot locate the PCI bus on the server.
Action:
Go to “Diagnostic test programs” on page
10 to run the diagnostic
utility.
PCNTND-29
WARNING:
DMA number is not necessary for PCI
device.
Explanation:
The Ethernet controller does not require a DMA setting.
Action:
Remove the DMA setting in the PROTOCOL.INI file.
PCNTND-33
PCNET device with specified IOBASE is already in use.
Explanation:
The specified I/O address number is already in use by another
Ethernet controller or device.
Action:
Remove the I/O address setting in the PROTOCOL.INI file.
Netfinity 5000 - Type 8659
37