IBM 9114-275 Installation Guide - Page 48

Adding or Replacing a Non-Hot-Pluggable PCI Adapter, PCI Adapter Placement Reference, firmly

Get IBM 9114-275 - IntelliStation POWER 275 PDF manuals and user guides View all IBM 9114-275 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

18. Power on the system as described in "Starting the System" on page 25. 19. Replace the bezel door if it was removed in one of the previous steps. Adding or Replacing a Non-Hot-Pluggable PCI Adapter To add or install an adapter, do the following: 1. Place the system into the service position as described in "Placing the Model 275 into the Service and Operating Position" on page 26. 2. Shut down the system as described in "Stopping the System" on page 25. 3. Disconnect the power source to the system. Note: This system may be equipped with a second power supply. Before continuing with this procedure, ensure that the system has been completely disconnected from its power source. 4. Remove the service access cover as described in "Service Access Cover Removal" on page 28. 5. Refer to the PCI Adapter Placement Reference for information regarding slot restrictions for adapters that can be used in this system. 6. If necessary, remove the adapter expansion slot shield. 7. Before handling any card, board, or memory DIMM, be sure to use your electrostatic discharge strap to minimize static-electric discharge. Refer to "Handling Static-Sensitive Devices" on page 24. 8. If necessary, remove the adapter from the antistatic package. Attention: Avoid touching the components and gold-edge connectors on the adapter. 9. Place the adapter, component-side up, on a flat, static-protective surface. 10. Set any jumpers or switches as instructed by the adapter's manufacturer documentation. 11. Carefully grasp the adapter by its top edge, and align the adapter with the expansion slot and its connector on the PCI riser card. 12. Press the adapter firmly into its connector. Attention: When you install an adapter into the system, be sure that it is completely and correctly seated in its connector. 32 IntelliStation POWER 9114 Model 275 Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
18.
Power on the system as described in “Starting the System” on page 25.
19.
Replace the bezel door if it was removed in one of the previous steps.
Adding or Replacing a Non-Hot-Pluggable PCI Adapter
To add or install an adapter, do the following:
1.
Place the system into the service position as described in “Placing the Model 275 into the Service
and Operating Position” on page 26.
2.
Shut down the system as described in “Stopping the System” on page 25.
3.
Disconnect the power source to the system.
Note:
This system may be equipped with a second power supply. Before continuing with this
procedure, ensure that the system has been completely disconnected from its power source.
4.
Remove the service access cover as described in “Service Access Cover Removal” on page 28.
5.
Refer to the
PCI Adapter Placement Reference
for information regarding slot restrictions for adapters
that can be used in this system.
6.
If necessary, remove the adapter expansion slot shield.
7.
Before handling any card, board, or memory DIMM, be sure to use your electrostatic discharge strap
to minimize static-electric discharge. Refer to “Handling Static-Sensitive Devices” on page 24.
8.
If necessary, remove the adapter from the antistatic package.
Attention:
Avoid touching the components and gold-edge connectors on the adapter.
9.
Place the adapter, component-side up, on a flat, static-protective surface.
10.
Set any jumpers or switches as instructed by the adapter’s manufacturer documentation.
11.
Carefully grasp the adapter by its top edge, and align the adapter with the expansion slot and its
connector on the PCI riser card.
12.
Press the adapter
firmly
into its connector.
Attention:
When you install an adapter into the system, be sure that it is completely and correctly
seated in its connector.
32
IntelliStation POWER 9114 Model 275 Installation Guide