IBM 9114-275 Installation Guide - Page 71

processor . Refer to Power Supply Removal on and Removing the Service Processor

Get IBM 9114-275 - IntelliStation POWER 275 PDF manuals and user guides View all IBM 9114-275 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Number M4 M5 M6 M7 M8 Description Memory slot 4 (J2A) Memory slot 5 (J0A) Memory slot 6 (J0B) Memory slot 7 (J1A) Memory slot 8 (J1B) Location Code U0.1-P1-M4 U0.1-P1-M5 U0.1-P1-M6 U0.1-P1-M7 U0.1-P1-M8 6. If necessary to access the DIMM slots, remove components such as power supplies or the service processor . Refer to "Power Supply Removal" on page 38 and "Removing the Service Processor Assembly" on page 57. 7. If necessary, remove the current memory DIMM from the desired location as described in "Memory DIMM Removal" on page 56 8. Before handling any card, board, or memory DIMM, touch any metal surface of the chassis with one hand to minimize the static electricity discharge. Refer to "Handling Static-Sensitive Devices" on page 24. 9. Remove the new memory DIMM from its antistatic package. 10. Ensure that the connector locking tabs are pushed out in the unlocked position,as shown in the following illustration, before installing a new memory DIMM. 11. Carefully grasp the memory DIMM along two edges and align the connector. 12. Insert the memory card firmly into the connector. 13. Secure the memory DIMM with the locking tabs located at each end of the DIMM connector, as shown in the following illustration. Attention: To prevent damage to the memory DIMM and the memory DIMM connectors, open or close the retention latches at the same time. 1 Locking Tabs (unlocked position) 2 Locking Tabs (locked position) 14. If they were removed to gain access to the DIMM slots, replace components such as power supplies or the service processor. Refer to "Power Supply Replacement" on page 40 and "Replacing the Service Processor Assembly" on page 57. 15. Replace the fan tray assembly as described in "Replacing the Fan Tray Assembly" on page 37. 16. Replace the service access cover as described in "Service Access Cover Replacement" on page 28. 17. Reconnect all power and signal cables. 18. Return the system to the operating position as described in "Placing the Model 275 into the Service and Operating Position" on page 26. 19. Power on the system as described in "Starting the System" on page 25. Chapter 3. Installing Options 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Number
Description
Location Code
M4
Memory slot 4 (J2A)
U0.1-P1-M4
M5
Memory slot 5 (J0A)
U0.1-P1-M5
M6
Memory slot 6 (J0B)
U0.1-P1-M6
M7
Memory slot 7 (J1A)
U0.1-P1-M7
M8
Memory slot 8 (J1B)
U0.1-P1-M8
6.
If necessary to access the DIMM slots, remove components such as power supplies or the service
processor . Refer to “Power Supply Removal” on page 38 and “Removing the Service Processor
Assembly” on page 57.
7.
If necessary, remove the current memory DIMM from the desired location as described in “Memory
DIMM Removal” on page 56
8.
Before handling any card, board, or memory DIMM, touch any metal surface of the chassis with one
hand to minimize the static electricity discharge. Refer to “Handling Static-Sensitive Devices” on
page 24.
9.
Remove the new memory DIMM from its antistatic package.
10.
Ensure that the connector locking tabs are pushed out in the unlocked position,as shown in the
following illustration, before installing a new memory DIMM.
11.
Carefully grasp the memory DIMM along two edges and align the connector.
12.
Insert the memory card firmly into the connector.
13.
Secure the memory DIMM with the locking tabs located at each end of the DIMM connector, as
shown in the following illustration.
Attention:
To prevent damage to the memory DIMM and the memory DIMM connectors, open or
close the retention latches at the same time.
1
Locking Tabs (unlocked position)
2
Locking Tabs (locked position)
14.
If they were removed to gain access to the DIMM slots, replace components such as power supplies
or the service processor. Refer to “Power Supply Replacement” on page 40 and “Replacing the
Service Processor Assembly” on page 57.
15.
Replace the fan tray assembly as described in “Replacing the Fan Tray Assembly” on page 37.
16.
Replace the service access cover as described in “Service Access Cover Replacement” on page 28.
17.
Reconnect all power and signal cables.
18.
Return the system to the operating position as described in “Placing the Model 275 into the Service
and Operating Position” on page 26.
19.
Power on the system as described in “Starting the System” on page 25.
Chapter 3. Installing Options
55