IBM 9114-275 Installation Guide - Page 54

Power Supply, Power Supply Removal, DANGER

Get IBM 9114-275 - IntelliStation POWER 275 PDF manuals and user guides View all IBM 9114-275 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Power Supply DANGER Do not attempt to open the covers of the power supply. Power supplies are not serviceable and are to be replaced as a unit. D02 This system unit can have up to two power supplies. If you are installing an option that requires removal of the power supplies, perform the procedures below. If you are replacing a power supply, go to "Power Supply Replacement" on page 40. If you are installing a second power supply as an optional feature, go to "Installing a Power Supply" on page 41 Power Supply Removal Before performing any of the following procedures, read and understand all of the safety notices beginning with "Safety Notices" on page vii. To install options on the system backplane, you must first remove the power supplies. Do the following: 1. Open the bezel door. 2. Shut down the system as described in "Stopping the System" on page 25. 3. Remove the service access cover as described in "Service Access Cover Removal" on page 28. 4. Remove the power cable from the rear of the power supply. 5. Wait at least 10 seconds before performing the next step. 6. Grasp the ends of both power supply handles, and slide the retractable spring-activated portion of each handle toward its hinged base. This action releases the locking tab located on the bottom side of each release handle. See the following illustration. 1 Power supply 2 Power supply handle latch 3 Retractable spring-activated portion of the handle 4 Fault LED (Amber) 5 DC Good LED (Green) 6 AC Good LED (Green) 7. Lift the handle until it is perpendicular (90 degrees) to the top of the power supply. By placing the handle perpendicular to the top of the power supply, the base or hinged portion of each handle acts as 38 IntelliStation POWER 9114 Model 275 Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Power Supply
DANGER
Do not attempt to open the covers of the power supply. Power supplies are not serviceable and
are to be replaced as a unit.
D02
This system unit can have up to two power supplies. If you are installing an option that requires removal of
the power supplies, perform the procedures below. If you are replacing a power supply, go to “Power
Supply Replacement” on page 40. If you are installing a second power supply as an optional feature, go to
“Installing a Power Supply” on page 41
Power Supply Removal
Before performing any of the following procedures, read and understand all of the safety notices beginning
with “Safety Notices” on page vii.
To install options on the system backplane, you must first remove the power supplies. Do the following:
1.
Open the bezel door.
2.
Shut down the system as described in “Stopping the System” on page 25.
3.
Remove the service access cover as described in “Service Access Cover Removal” on page 28.
4.
Remove the power cable from the rear of the power supply.
5.
Wait at least 10 seconds before performing the next step.
6.
Grasp the ends of both power supply handles, and slide the retractable spring-activated portion of
each handle toward its hinged base. This action releases the locking tab located on the bottom side of
each release handle. See the following illustration.
1
Power supply
4
Fault LED (Amber)
2
Power supply handle latch
5
DC Good LED (Green)
3
Retractable spring-activated portion of the
handle
6
AC Good LED (Green)
7.
Lift the handle until it is perpendicular (90 degrees) to the top of the power supply. By placing the
handle perpendicular to the top of the power supply, the base or hinged portion of each handle acts as
38
IntelliStation POWER 9114 Model 275 Installation Guide