IBM HC10 User Guide - Page 33

Attention, Important

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

5. Open the blade workstation cover (see "Opening the blade workstation cover" on page 17 for instructions). DIMM 2 DIMM 4 DIMM 1 DIMM 2 connector DIMM 3 DIMM 4 connector 6. Locate the DIMM connectors on the system board (see the illustration), and determine the connectors into which you will install the DIMMs. 7. Touch the static-protective package that contains the DIMM optional device to any unpainted metal surface on the BladeCenter unit or any unpainted metal surface on any other grounded rack component in the rack that you are installing the DIMM in for at least 2 seconds; then, remove the DIMM from its package. 8. Complete the following steps for each DIMM that you install: a. Open the retaining clips on the DIMM connector. b. Turn the DIMM so that the DIMM keys align correctly with the connector on the system board. Attention: To avoid breaking the retaining clips or damaging the DIMM connectors, handle the clips gently. c. Insert the DIMM by pressing the DIMM along the guides into the connector. Make sure that the retaining clips snap into the closed position. Important: If there is a gap between the DIMM and the retaining clips, the DIMM has not been correctly installed. Open the retaining clips and remove the DIMM; then, reinsert the DIMM. If you have other devices to install or remove, do so now; otherwise, go to "Completing the installation" on page 22. Chapter 3. Installing optional devices 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
5.
Open
the
blade
workstation
cover
(see
“Opening
the
blade
workstation
cover”
on
page
17
for
instructions).
DIMM 2
DIMM 1
DIMM 2 connector
DIMM 4
DIMM 3
DIMM 4 connector
6.
Locate
the
DIMM
connectors
on
the
system
board
(see
the
illustration),
and
determine
the
connectors
into
which
you
will
install
the
DIMMs.
7.
Touch
the
static-protective
package
that
contains
the
DIMM
optional
device
to
any
unpainted
metal
surface
on
the
BladeCenter
unit
or
any
unpainted
metal
surface
on
any
other
grounded
rack
component
in
the
rack
that
you
are
installing
the
DIMM
in
for
at
least
2
seconds;
then,
remove
the
DIMM
from
its
package.
8.
Complete
the
following
steps
for
each
DIMM
that
you
install:
a.
Open
the
retaining
clips
on
the
DIMM
connector.
b.
Turn
the
DIMM
so
that
the
DIMM
keys
align
correctly
with
the
connector
on
the
system
board.
Attention:
To
avoid
breaking
the
retaining
clips
or
damaging
the
DIMM
connectors,
handle
the
clips
gently.
c.
Insert
the
DIMM
by
pressing
the
DIMM
along
the
guides
into
the
connector.
Make
sure
that
the
retaining
clips
snap
into
the
closed
position.
Important:
If
there
is
a
gap
between
the
DIMM
and
the
retaining
clips,
the
DIMM
has
not
been
correctly
installed.
Open
the
retaining
clips
and
remove
the
DIMM;
then,
reinsert
the
DIMM.
If
you
have
other
devices
to
install
or
remove,
do
so
now;
otherwise,
go
to
“Completing
the
installation”
on
page
22.
Chapter
3.
Installing
optional
devices
21